Frigidaire 137153200A manual Operating

Page 12

Avoid Service Checklist, continued

OCCURRENCE

POSSIBLE CAUSE

SOLUTION

OPERATING

 

 

 

 

 

Washer does not start.

Washer lid is open.

Close washer lid. The washer will not fill with water, agitate or spin

 

 

when the lid is open, and will only start to do so if the lid is closed.

Electrical power cord may not be plugged in or connection may be loose.

Make sure plug fits tightly in wall outlet.

House fuse blown, circuit breaker tripped, or a power outage has occurred.

Reset circuit breaker or replace fuse. Do not increase fuse capac- ity. If problem is a circuit overload, have it corrected by a qualified electrician. If problem is a power outage, call local electric company.

 

Water supply faucets are not turned on.

Turn on water supply faucets.

 

Cycle selector is not in correct position.

Move indicator clockwise slightly. Pull out knob.

 

 

 

 

Motor is overheated. Washer motor will stop if it

It will automatically restart after a cool down period of up to 30

 

becomes overheated.

minutes (if washer has not been manually turned off).

 

 

 

Washer won’t spin.

Lid is not completely closed.

Close washer lid. The washer will not fill with water, agitate or spin

 

 

when the lid is open, and will only start to do so if the lid is closed.

Residue left in drum.

Heavily soiled items.

Wipe drum with a nonabrasive household cleanser, then rinse.

 

 

Shake or brush excess dirt and sand from items before washing

WATER

 

 

 

 

 

Wash load too wet after

Washer is overloaded.

Do not overload washer. See Washing Procedures.

spin.

 

 

Load is out of balance.

Rearrange load to allow proper spinning.

 

 

 

 

 

Drain hose is kinked.

Straighten drain hose.

 

 

 

Water does not enter

Washer lid is open.

Close washer lid. The washer will not fill with water, agitate or spin

washer or it enters slowly.

 

when the lid is open, and will only start to do so if the lid is closed.

 

Water supply is not adequate in area.

Check another faucet in the house. Wait until water supply and

 

 

pressure increase.

 

 

 

 

Water supply faucets are not completely open.

Fully open hot and cold faucets.

 

 

 

 

Water is being used elsewhere in the house.

Water pressure must be at least 30 psi (260 kPa). Avoid running

 

 

water elsewhere while washer is filling.

 

Water inlet hoses are kinked.

Straighten hoses.

 

 

 

Water level does not

Improper water level selection (for models with

cover load.

water level/load size control).

Select higher water level/load size.

Washer is overloaded.

Do not overload washer. Dry load level should not be higher

 

than top of agitator vanes.

Warm or hot water is not hot enough.

Hot water heater is set too low or is a distance

Measure hot water temperature at nearby faucet with candy or

from washer.

meat thermometer. Water temperature should be at least 120°F

 

(50°C). Adjust water heater as necessary.

 

 

Hot water is being used elsewhere in the house.

Avoid using hot water elsewhere before or during washer use.

 

There may not be enough hot water available for proper clean-

 

ing. If problem persists, your hot water system may be unable to

 

support more than 1 use at a time.

Water in washer does not

Drain hose is kinked or clogged.

drain or drains slowly.

 

Clean and straighten the drain hose.

Water leaks.

Loose fill hose connection at faucet or washer.

Check and tighten hose connections. Install rubber sealing wash- ers provided.

 

House drain pipes are clogged.

Unclog drain pipes. Contact plumber if necessary.

Incorrect wash and rinse

Hot and cold water hoses are connected to wrong

Connect hot water hose to hot water faucet and cold water

temperatures.

supply faucets.

hose to cold water faucet.

Water is entering washer

Drain hose standpipe is incorrect height.

Standpipe must be a minimum of 33” (83.82 cm) high to pre-

but tub does not fill.

 

vent siphoning. See INSTALLATION INSTRUCTIONS.

 

 

 

Water is present in tub after

Lid lock malfunction.

Do not bypass lid lock. Call your authorized servicer.

wash cycle is complete.

 

 

 

 

 

The drain and spin cycles

Lid lock malfunction.

Do not bypass lid lock. Call your authorized servicer.

did not occur.

 

 

12

Image 12
Contents Use & Care Guide Table of Contents Protect Children Prevent InjuryPrevent Injury and Damage to the Washer Washing Procedures Sort laundry into loads that can be washed togetherPrepare items for washing Pretreat stains and heavy soilDo not Remove Service CAP Found Inside the Agitator Post Remove items when the cycle is completedSafety LID Lock Add laundry load to washerCycle Settings Cycle SelectionFor best results WASH/RINSE Temperature Cycle OptionsEnergy Saving Tips Load SizeSafe Stain Removal Procedures For Successful Stain RemovalStain Removal Suggestions Stain TreatmentCare and Cleaning Inside OutsideCommon Washing Problems Winterizing InstructionsAvoid Service Checklist NoiseOperating Major Appliance Warranty Information