![](/images/new-backgrounds/1320598/3205989x1.webp)
INSTALLATION
REQUIREMENTS
Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer basket.
Tools needed for connecting the drain hose and water inlet hoses:
•Pliers that open to 19/16in. (3.95 cm)
•Flashlight (optional)
Parts supplied:
3 | 4 | 5 |
1.Drain hose
2.Silver,
3.Yellow,
4.Water inlet hoses (2)
5.Flat water inlet hose washers (4)
Tools needed for securing the drain hose and leveling the washer.
•Adjustable or open end wrench %6in. (14 mm)
•Level
•Wood block
•Ruler or measuring tape
Parts supplied:
12
1.Shipping strap with fastener
2.Front leveling feet with nuts (2)
Alternate Parts
Parts listed are available from your local Sears store or Sears Service Center. For further information, please call
If You Have: | You Will Need to Buy: |
|
| ||||||
Laundry tub or | Sump | pump |
| system | (if not already | ||||
standpipe | taller | available) |
|
|
|
|
| ||
than 96 in. (2.4 m) |
|
|
|
|
|
|
|
| |
1 in. (2.5 cm) | 2 in. (5 cm) diameter | to | 1 in. (2.5 cm) | ||||||
diameter |
| diameter | standpipe adapter, Part No. | ||||||
standpipe |
| 3363920 |
|
|
|
|
|
| |
Overhead | sewer | Standard | 20 gaL (76 L) 39 in. (99 cm) tall | ||||||
|
| drain tub or utility sink, sump pump and | |||||||
|
| connectors | (available | from | local | ||||
|
| plumbing | suppliers) |
|
|
| |||
Floor drain |
| Siphon | break, Part Number | 285320; | |||||
|
| additional drain hose, Part Number | |||||||
|
| 3357090 | and | connector | kit, | ||||
|
| Part Number | 285442 |
|
|
| |||
Water faucets | 2 longer | water fill hoses: |
|
| |||||
beyond reach of | 6 ft (1.8 m) Part Number | 76314, | |||||||
fill hoses |
| 10 ft (3.0 m) Part Number 350008 | |||||||
Drain hose | too | Drain hose, | Part No. 388423 and hose | ||||||
short |
| kit, Part | No. | 285442 |
|
|
|
Drain hose that is Hose kit, Part No. 285442 too long
Lint clogged drain Drain protector, Part No. 367031
Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room, closet, or recessed area. (See "Drain System.")
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
•A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. (See "Electrical Requirements.")
Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not recommended.
•A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for winterizing information.