![](/images/new-backgrounds/1320598/32059829x1.webp)
Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather, winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time, you should:
•Unplug washer or disconnect power.
•Turn off the water supply to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away.
To winterize washer:.
1.Shut off both water faucets.
2.Disconnect and drain water inlet hoses.
3.Put 1 qt (1 L) of
4.Run washer on an Extended Spin cycle.
5.Unplug washer or disconnect power.
To use washer again:
1.Flush water pipes and hoses.
2.Reconnect water inlet hoses.
3.Turn on both water faucets.
4.Plug in washer or reconnect power.
5.Run the washer through any cycle with _/; the normal
recommended amount of detergent to clean out the antifreeze.
To transport the washer:.
1.Shut off both water faucets.
2.Disconnect and drain water inlet hoses.
3.If washer will be moved during freezing weather, put in 1 qt (1
L)of
4.Disconnect the drain from the drain system.
5.Unplug the power cord.
6.Place the inlet hoses into the basket.
7.Drape the power cord and drain hose over edge into the basket.
8.Place the expanded foam plug retained from the washer's shipping material into basket opening. Close the lid and put a piece of tape over the lid and down to the front of the washer.
Re-installing the washer
1.Follow the "Installation Instructions" to locate, level and connect the washer.
2.Run the washer through any cycle with _/; the normal recommended amount of detergent to clean out the antifreeze, if used.
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid
the cost of a service call...
Washer won't fill, rinse or wash
Does the water level seem too low, or does the washer appear to not fill completely?
This washer uses very little water and never fills completely. Water will not be seen over the top of the wash plate.
•Checkthe following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug? Check electrical source or call electrician.
Are the hot and cold water faucets turned on? Is the water inlet hose kinked?
Are the water inlet valve screens clogged?
Washer stops
•Checkthe following:
Is the power cord plugged into a grounded 3 prong outlet? Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Are the water inlet valve screens clogged?
•Is there power at the plug?
Check electrical source or call electrician.
•Has a fuse blown or has the circuit breaker tripped? If problem continues, call electrician.
•Are you using an extension cord? Do not use an extension cord.
Is the Cycle Selector Control (Timer) knob lined up and pulled out?
Turn Cycle Selector Control (Timer) knob to cycle and pull out to start washer. If washer still doesn't start, push knob back in, turn slightly to the right and pull out again.
Is the washer overloaded?
Wash smaller loads. See "Starting Your Washer" for maximum load size.
Washer won't drain or spin
Is the drain hose clogged, or the end of the drain hose more than 96 in. (244 cm) above the floor?
See "Installation Instructions" for proper installation of drain hose.
Is the lid open?
The lid must be closed during operation.
Is there excessive sudsing?
Use less detergent. Follow manufacturer's directions.
Is your voltage low?
Check electrical source or call electrician. Do not use an extension cord.
15