How to run a wash cycle or a drying cycle

How to run a wash cycle or a drying cycle

1. SWITCH THE MACHINE ON. Press the button;

GB the START/PAUSE indicator light will flash slowly in a green colour.

2.LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page.

3.MEASURE OUT THE DETERGENT. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Detergents and laundry”.

4.CLOSE THE DOOR.

5.SELECT THE WASH CYCLE. Set the WASH CYCLE knob to the desired programme; a temperature and spin speed is set for each wash cycle; these may be adjusted. The duration of the cycle will appear on the display.

6.CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modifying the temperature and/or spin speed. The machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most recently-used settings if they are compatible with the selected cycle. The

temperature can be decreased by pressing the button, until the cold wash “OFF” setting is reached. The spin speed may be progressively reduced by

pressing the button, until it is completely excluded (the “OFF” setting). If these buttons are pressed again, the maximum values are restored.

Setting the drying cycle

The first time the button is pressed, the machine will automatically select the maximum drying cycle which is compatible with the selected wash cycle. Subsequent presses will decrease the drying level and then the drying time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level: Iron dry: suitable for clothes which will need ironing afterwards. the remaining dampness softens creases, making them easier to remove; “A1” appears on the display.

Hanger dry: ideal for clothes which do not need to be dried fully; “A2” appears on the display.

Cupboard dry: suitable for laundry which can be put back in a cupboard without being ironed; “A3” appears on the display.

Extra dry: suitable for garments which need to be dried completely, such as sponges and bathrobes “A4”; appears on the display.

B - Based on a set time period: between 30 and 180 minutes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back in the drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the load.

N.B: a cooling-down period is always added to the end of each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle (11-12) in accordance with the type of fabric. The desired drying level or time may also be set using the DRYING button .

Modifying the cycle settings.

•Press the button to enable the option; the indicator light corresponding to the button will switch on.

•Press the button again to disable the option; the indicator light will switch off.

!If the selected option is not compatible with the programmed wash cycle, the indicator light will flash and the option will not be activated.

!If the selected option is not compatible with another option which has been selected previously, the indicator light corresponding to the first option selected will flash and only the second option will be activated; the indicator light corresponding to the enabled option will remain lit.

!The options may affect the recommended load value and/or the duration of the cycle.

7.START THE PROGRAMME. Press the START/PAUSE button. The corresponding indicator light will become green, remaining lit in a fixed manner, and the door will

be locked (the DOOR LOCKED symbol will be on). To change a wash cycle while it is in progress, pause the Washer-dryer using the START/PAUSE button (the START/PAUSE indicator light will flash slowly in an orange colour); then select the desired cycle and press the START/PAUSE button again. To open the door while a cycle is in progress, press the START/PAUSE button;

if the DOOR LOCKED symbol is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at which it was interrupted.

8.THE END OF THE WASH CYCLE. This will be indicated by the text “End” on the display; when the

DOOR LOCKED symbol switches off the door may be opened. Open the door, unload the laundry and switch off the machine.

!If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped and the machine will switch off.