Frigidaire FARE4044MW Avoid Service Checklist, Occurrence Possible Cause Solution

Page 15

SOLUTIONS TO COMMON PROBLEMS

Avoid Service Checklist

Before calling for service, review this list. It may save both time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this dryer.

OCCURRENCE	POSSIBLE CAUSE	SOLUTION

Dryer does not start.	Electrical power cord is not securely plugged in or plug	Make sure the plug ﬁts tightly in wall outlet.
	may be loose.

	House fuse blown or circuit breaker tripped.	Reset circuit breaker or replace fuse.

		Make sure electrical line is not overloaded and the dryer is on a
		separate circuit.

	Thermal limiter tripped.	Call authorized service person for replacement.

Dryer runs but won’t	There are 2 house fuses in the dryer circuit. If 1 of the 2	Replace fuse.
heat.	fuses is blown, the drum may turn but the heater will not
	operate. (electric models)

Gas supply valve is not open (gas models).

Check to make sure supply valve is open. See INSTALLATION INSTRUCTIONS for procedure.

		Dryer does not have enough air supply to support the	See INSTALLATION INSTRUCTIONS.
		burner ﬂame (gas models).

		LP gas supply tank is empty or there has been a utility	Reﬁll or replace tank.
		interruption of natural gas (gas models).	Dryer should heat when utility service is restored.
			Dryer should heat when utility service is restored.

	Drying cycle takes too	Lint ﬁlter is clogged with lint.	Make sure all lint has been removed from the dryer lint ﬁlter
	long, outside of the		before starting each cycle.
	dryer feels too hot or
	dryer feels too hot or	Exhaust duct requirements have not been met.	Exhaust duct must be at least 4 inches in diameter and made
	smells hot.	Exhaust duct requirements have not been met.	Exhaust duct must be at least 4 inches in diameter and made
	smells hot.		of rigid or semi-rigid metal.
			of rigid or semi-rigid metal.

			When in place, the duct must have no more than four 90°
			bends and must not exceed length listed in INSTALLATION
			INSTRUCTIONS.

		Electric dryer is connected to a 208 volt circuit.	Drying time will be 20% longer than drying on a 240 volt
			circuit.

		Drying procedures have not been followed.	See “Operating Instructions.”

		Outside exhaust hood or exhaust duct may be clogged	Clean out any obstruction.
		or restricted.

		High humidity.	Use a dehumidiﬁer near the dryer.

	Excessive wrinkling.	Dryer is overloaded.	Do not overload. See “Operating Instructions.”

		Items left in dryer too long.	Remove items as soon as cycle ends.

		Insufﬁcient sorting of items.	See “Operating Instructions.”

		Drying temperature too high.	Follow fabric care label instructions.

	Scratching or chipping	Foreign objects such as coins, pins, clips or buttons	Always remove foreign objects from pockets before laundering.
	of the drum ﬁnish.	are inside the dryer.*	Remove objects from drum and restart dryer.

		Permanently attached items such as belt buckles,	It may be necessary to sew a scrap of material securely around
		zippers and fasteners may be hitting the inside of the	ornaments before drying to prevent scratching and damage to
		drum.*	the dryer.

*Drum damage caused by foreign objects or permanently attached items is not covered by the warranty.

15

Image 15

Contents Use &Care Important Safety Instructions Electric Dryer Protect Children Prepare load for drying Operating InstructionsNormal Operating Sounds Operating Your DryerStart the cycle Check that the lint ﬁlter is clean and in placeSelect the appropriate cycle and settings for each load Load the dryer and close the doorInitial Calculating Estimated Cycle SelectionFor best results Auto Dry CyclesTowels CasualNormal Heavy dutyCycle Settings For best results Cycle Options Dryer Settings Chart Other Features Inside Care and CleaningCommon Drying Problems Solutions to Common ProblemsOccurrence Possible Cause Solution Avoid Service ChecklistWarranty Periods Major Appliance Warranty Information