Hotpoint BHWDD 74, Hotpoint washer dryer instruction manual Instructions for the fitter

Page 6

 

Instructions for the fitter

GB

 

 

Mounting the wooden panel onto the door

 

 

and inserting the machine into cabinets:

 

In the case where the machine must be shipped

 

for final installation after the wooden panel has

 

been mounted, we suggest leaving it in its ori-

 

ginal packaging. The packaging was designed

 

to make it possible to mount the wooden panel

 

onto the machine without removing it completely

 

(see figures below).

 

The wooden panel that covers the face of

 

the machine must not be less than 18 mm in

 

thickness and can be hinged on either the right

 

or left. For the sake of practicality when using

 

the machine, we recommend that the panel be

 

hinged on the same side as the door for the

 

machine itself - the left.

Door Mounting Accessories (Fig. 1-2-3-4-5).

 

N° 2 Hinge Supports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N° 2 Hinges

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 1

Fig. 2

N° 1 Magnet

N° 1 Magnet plate

Fig. 3

Fig. 4

AB

CD

E

 

N° 1 Rubber plug

 

N° 4 Spacers

 

 

 

 

 

 

 

 

Fig. 5

Fig. 4/B

-No. 6 type A self-threading screws, l =13 mm.

-No. 2 type B metric, countersunk screws, l =25; for fastening the magnet plate to the cabinet.

-No. 4 type C metric screws, l =15 mm; for mounting the hinge supports to the cabinet.

-No. 4 type D metric screws, l =7 mm; for mounting the hinges on the supports.

Mounting the Parts onto the Face of the Machine.

-Fit the hinge supports to the appliance front panel, positioning the hole marked with an arrow in fig. 1 so that it is on the inner side of the front panel. Fit a spacer (fig. 4/B) between the surfa- ces using type C screws.

-Fit the magnet plate at the top of the opposite side, using type B screws to fix two spacers (fig. 4/B) between the plate and the surface.

6

Image 6
Contents Contents Instructions for useInstallation Unpacking and levellingElectric and water connections Removing the plug Correspond with the coloured markings iden As the colours of the wires in the lead may notFirst wash cycle Tifying the terminals in your plug, proceed asTechnical data Model2006/95/EC Low Voltage 2002/96/EC Instructions for the fitter Using the Drilling Template Accessories provided for the height adjustmentMounding the Parts onto the Wooden Panel Door Care and maintenance This appliance can be used by children aged Precautions and tipsGeneral safety DisposalDescription of the washer dryer Control panelDisplay How to run a wash cycle or a drying cycle Close the DoorWash cycles and functions Table of wash cyclesPreparing the laundry Detergents and laundryDetergent dispenser drawer Special wash cyclesTroubleshooting Problem Possible causes / SolutionsMachine vibrates a lot during GuaranteeGB AssistanceAfter Sales Service Page 195107786.00