Extron electronic RGB 464XI Cable the Rear Panel, Apply Power and Test the Interface, C D E

Cable the Rear Panel

A DIP Switches ­— Used to set options, see previous page.

B RGB video output connectors —­ Attach video cables from the interface to the display device using these female BNC connectors. See the video output connections diagram (below right) for the wiring diagrams.

6

7

8

2

3

C

D

E

Gain switch —­To compensate for longer cable runs, slide this switch to select the level of video gain that yields the sharpest picture.

Power connector — Connect a 9 to 24 VDC power supply to this
3.5 mm, 2-pole, direct insertion captive screw connector. Wire the	9	4	51	5
connector as shown below at right. Polarity is not important.
	Rear Panel Connections and Switches

Audio output connector — Insert wires into and tighten the

screws on this 3.5 mm, 5-pole, direct insertion captive screw connector for

unbalanced or balanced audio output. Wire the connector as shown in the	RGBHV
audio wiring diagrams below at right.	R-Red G-Green B-Blue H-Black V-Yellow

NOTE:	Items F, G, H, and I are features of the RGB 464xi
	interface only.

F Composite video pass-through BNC connector — A male BNC connector

attaches here.

G S-video pass-through 4-pin mini-DIN connector — A male 4‑pin mini-DIN

connector attaches here.

H Balanced active audio output connector — Insert wires into this 3.5 mm, 5-pole, direct insertion captive screw connector for balanced active audio output, then tighten the screws. Wire the connector as shown below at right.

I Network pass-throughRJ-45 connector — If this connector is not required, a blank cover is supplied to fill the opening.

RGBS

R-Red G-Green B-Blue S-Black Yellow

RGsB

R-Red	G-Green B-Blue Black Yellow
	Video Output Connections
VDC	 or 
24	 or 
9-

Power Connector Wiring

CAUTION:

Apply Power and Test the Interface

Apply power to the interface. The power LED on the front panel lights.

Before mounting into the wall, connect all input sources to the interface. Power up all AV devices connected to the interface. Check that all are working properly. If not, check cabling and switch settings, and make adjustments as necessary.

For an unbalanced stereo output, connect the sleeves to the ground contact.

DO NOT connect the sleeves to the negative (–) contacts.

NO GROUND HERE	R
Tip
Sleeve (s)
NO GROUND HERE	L
Tip

Unbalanced

Stereo Output

Disconnect Power and Mount the Interface

Disconnect power from all the devices except the interface.

Mount the interface as explained in the appropriate installation guide.

Connect Power

Once the interface is properly mounted, restore power to all connected devices. The interface is now ready for operation.

Ring	R
Tip
Sleeve (s)
Ring	L
Tip

Balanced

Stereo Output

Do not tin the wires!

Audio Wiring

Extron USA - West	Extron USA - East	Extron Europe	Extron Asia	Extron Japan	Extron China	Extron Middle East
Headquarters
+800.633.9876	+800.633.9876	+800.3987.6673	+800.7339.8766	+81.3.3511.7655	+400.883.1568	+971.4.2991800
				+81.3.3511.7656 FAX		+971.4.2991880 FAX
Inside USA/Canada Only	Inside USA/Canada Only	Inside Europe Only	Inside Asia Only		Inside China Only
+1.714.491.1500	+1.919.863.1794	+31.33.453.4040	+65.6383.4400		+86.21.3760.1568		68-542-50
+1.714.491.1517 FAX	+1.919.863.1797 FAX	+31.33.453.4050 FAX	+65.6383.4664 FAX		+86.21.3760.1566 FAX		Rev. B
							07 11
2	© 2011 Extron Electronics All rights reserved.			www.extron.com