Hotpoint WD645, WD640, WD440, WD420 Error message, Different load types need different drying times

Page 23

Something Wrong? - Troubleshooting

Section 2: All Aquarius Models - Problems with the Drying cycle?

GB

The laundry is not dry after using the dry programme.

Your machine uses cold water to condense the moisture extracted from the load Check that:

●Both of the cold water inlet hoses are connected to the cold water supply tap, using the ‘Y’ piece connector.

●The inlet hoses are not kinked.

●The cold water supply tap is turned on.

Different load types need different heat settings. Some need HIGH heat, some need LOW heat.

Check that:

●HIGH heat option has been selected if you are drying Cottons.

Different load types need different drying times.

Check that:

●The Drying time selected was sufficient for the load.

Description

 

 

Contents

 

 

Explained

WashLabels

 

 

Note: Your machine contains an out of balance spin protection device, if the out

 

 

of balance is too great the machine automatically spins at a lower speed. Check

 

 

that the load was spun correctly at the and of the wash cycle before the

 

 

machine advanced into the drying cycle, then try another rinse and spin and

 

 

repeat the drying cycle.

The load is warm at the end

●

A 20 minute ‘Cool Tumble’ period is included at the end of the drying cycle -

of the drying cycle.

 

Always allow the machine to complete the full drying cycle to ensure this cool

 

 

tumble period occurs.

The machine spins during

●

This is normal and is not a fault - The machine may sometimes spin during the

the drying cycle.

 

drying cycle to improve drying efficiency.

The Drying Times dial does

●

This is normal and is not a fault - You must always return the Drying Times dial

not count down (Aquarius

 

manually to the ‘Off’ position at the end of each drying cycle.

only).

 

 

Section 3: Specific Error Messages on the Control Panel

Your machine carries out automatic checks at various stages of the wash cycles - Error messages will be displayed on the control panel to indicate there is something wrong.

The error message displayed is dependent upon which machine you have:

Error message:

Installation

 

 

 

Features

ControlPanel

Modifiers

and Programmes Option

 

 

andLaundry

Detergents

 

 

Maintenance

Care

‘Wash’ indicator light is flashing on Aquarius models

OR

‘H20’flashing in the display on Aquarius+ models

‘Door Locked’ indicator

light is flashing on Aquarius models

OR

The display shows ‘door’ on Aquarius+ models

This indicates that the machine has failed to take in water (see Installation). Check that:

●both of the cold water inlet hoses are connected correctly to the cold water supply tap, using the ‘Y’ piece connector.

●the cold water inlet hoses are not kinked.

●the cold water supply tap is turned on... Ensure it is turned fully on.

●the water pressure is sufficient (see Technical Details Chart).

This indicates that the door is not closed properly.

●Close the door firmly and try the machine again.

 

and

 

 

andAdvice

Precautions

 

 

Troubleshooting

Wrong Something -

Service

 

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Instructions for Installation and Use Description Contents Wash Labels Explained Unpacking InstallationRepeat steps 1 to 4 to remove the second transit bolt Remove the transit fixingsLocation Hints and tips LevellingWater Connection Benefits of cold fillElectrical connections Before you start using your machineDrainage Connection Aquarius+ control panel Control Panel FeaturesAquarius control panel Starting a typical wash and dry programme Starting a ProgrammeDrying Setting drying programmesItems not suitable for tumble drying Important informationDrycare tips Programme Table Option modifiers Option Modifiers Special FeaturesSpecial features No water detection Automatic featuresEnergy saving and water levels Unbalanced load detectionDetergent dispenser Detergents and LaundryMoulded plug Care and maintenanceCleaning Cleaning the dispenser drawer and compartmentsRecycling and Disposal information Precautions and adviceGeneral safety Saving energy and respecting the environmentTechnical Details Chart Safety advicePossible causes / Solution Something Wrong? TroubleshootingProblem From behind or underneath This indicates that the door is not closed properly Error message‘Wash’ indicator light is flashing on Aquarius models Different load types need different drying timesSpare Parts ServiceBefore calling the Service Centre

WD645, WD440, WD640, WD420 specifications

The Hotpoint WD420, WD640, WD440, and WD645 are an impressive range of washer-dryers designed to meet the diverse needs of modern households. Each model is characterized by its combination of efficient washing and drying capabilities, making them ideal for those who value convenience without sacrificing performance.

The Hotpoint WD420, known for its compact design, is perfect for smaller living spaces. It boasts a 6 kg washing capacity and a 5 kg drying capacity, making it sufficient for individuals or small families. Its 1200 rpm spin speed ensures efficient water extraction, reducing drying time significantly. This model features the ‘Anti-Ageing’ program, which uses lower temperature washes and spins to help protect delicate fabrics, prolonging their lifespan.

In contrast, the WD640 offers a more extensive capacity, with a 7 kg washing and a 5 kg drying capability. This model introduces advanced features such as the ‘Rapid Wash’ program, which allows users to wash small loads in just 30 minutes - ideal for those busy days when time is of the essence. It also includes a sensor drying function, which adjusts the drying time based on the moisture levels in the drum, ensuring energy efficiency and protecting clothes from overdrying.

The WD440 enhances the drying experience with its 6 kg washing and 5 kg drying capacities. A notable characteristic of this model is its ‘Cotton’ cycle, designed specifically to handle cotton fabrics like shirts and bed linens, providing optimal cleaning and drying. Additionally, the model includes a delay timer, allowing users to set the appliance to start at their convenience, a great feature for balancing busy schedules.

Finally, the WD645 epitomizes versatility, featuring a larger washing capacity of 8 kg and a drying capacity of 6 kg. It comes equipped with Smart Technology, which utilizes sensors to monitor load size and optimize wash cycles for the best performance. The model also features a special ‘Wool’ cycle, ensuring that woolen items are washed gently, thus preventing any shrinkage or damage.

Together, these Hotpoint washer-dryer models combine innovative technologies with user-friendly features such as various wash programs, energy efficiency, and compact designs. They truly cater to the needs of contemporary life, making laundry tasks simpler and more efficient, benefiting households of all sizes and lifestyles.
Top Page Image Contents