Hotpoint WD645, WD640, WD440 Levelling, Water Connection, Benefits of cold fill, Hints and tips

Page 7

Installation

Levelling

Your machine will be noisy if the two front feet are not adjusted so that the machine stands firm and level.

!The machine must be levelled from side to side and from front to back.

1.Move your machine into its final location, taking care not to trap or kink the hoses.

2.Turn one or both front feet

anti-clockwise by hand until the feet cannot be turned any more. When adjusting the feet, use a spirit level to check the machine stands level, from side to side and from front to back.

The spring on each foot will stop them coming loose.

!If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the machine.

Water Connection

Connecting the cold water inlet hoses with the ‘Y’ piece connector.

!Remember: please use the new hoses supplied, fitted to the machine. Old hoses may cause leaks due to worn out washers or may be split due to water pressure.

!Remember: This is a cold-fill machine... BOTH fill hoses (blue connectors) fitted to the rear of the machine MUST be connected to the COLD water supply (via the ‘Y’ piece connector).

!Before making connections to the cold water supply, allow the water to run freely from the supply tap until it is perfectly clear.

COLD

WATER

SUPPLY

‘Y’ piece connector

Cold water fill hose (Blue Connectors)

1.Screw the ‘Y’ piece connector onto the cold water supply until tight.

2.Fit a 3/4" sealing cap to the hot water supply, to prevent unused supply leaking.

3.Turn ON the COLD water supply tap and check for leaks, tighten if necessary.

4.Leave the unused HOT water supply turned OFF.

!We recommend fitting a 3/4" sealing cap to the hot water supply tap (if present), to ensure there are no leaks. Sealing caps can be purchased from Hotpoint Service on 08709 077 077 or all good DIY and Plumbing outlets.

Benefits of cold fill

●Modern detergents are designed to give the best cleaning results at low temperatures. Biological detergents contain enzymes which are active between 30˚C and 53˚C, giving greater results at lower temperatures.

●Cold water relaxes fabrics, whilst hot water can seal in stains.

●Improved stain removal with cold water.

●The most commonly used programme at present is 40˚C, which will take on cold water even if hot and cold were available.

●You can heat the water required to finish the wash cycle, which makes it more economical than taking water heated in a tank by an immersion heater or gas boiler.

Hints and tips

!Make sure there are no kinks or bends in the hose.

!The water pressure at the supply tap must be within the values indicated in the Technical Details table (see page 20).

!If the water inlet hoses are not long enough, you can purchase an extended hose from Hotpoint Service on 08709 077 077.

!Always use a new inlet hose.

!Check the water inlet hose at least once a year, replace if cracked as worn hoses could split under water pressure.

!Turn on the water supply and check that the connections do not leak. If there is a leak, turn off the water supply, disconnect the hoses and check that the sealing washers are in place. Refit the hoses and turn on the water supply.

GB

Description

 

 

 

 

 

Contents

 

 

 

 

 

Explained

WashLabels

 

 

 

 

Installation

 

 

 

 

 

Features

Panel

Control

 

 

 

Modifiers

andOption

Programmes

 

 

 

andLaundry

Detergents

 

 

 

 

Maintenance

Careand

 

 

 

 

andAdvice

Precautions

 

Did you know?...

●...the most common cause of problems with water connection is that the customer has not turned the supply tap on..

●...it is very important to ensure that your hoses or cables are not kinked or squashed when the machine is pushed back into its location, as this can lead to your machine failing to fill or empty the water.

●...the majority of problems with noisy machines are due to the feet not being adjusted correctly to level the machine.

Troubleshooting

Wrong Something -

Service

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Instructions for Installation and Use Description Contents Wash Labels Explained Unpacking InstallationLocation Remove the transit fixingsRepeat steps 1 to 4 to remove the second transit bolt Hints and tips LevellingWater Connection Benefits of cold fillDrainage Connection Before you start using your machineElectrical connections Aquarius control panel Control Panel FeaturesAquarius+ control panel Starting a typical wash and dry programme Starting a ProgrammeDrying Setting drying programmesDrycare tips Important informationItems not suitable for tumble drying Programme Table Option modifiers Option Modifiers Special FeaturesSpecial features No water detection Automatic featuresEnergy saving and water levels Unbalanced load detectionDetergent dispenser Detergents and LaundryMoulded plug Care and maintenanceCleaning Cleaning the dispenser drawer and compartmentsRecycling and Disposal information Precautions and adviceGeneral safety Saving energy and respecting the environmentTechnical Details Chart Safety adviceProblem Something Wrong? TroubleshootingPossible causes / Solution From behind or underneath This indicates that the door is not closed properly Error message‘Wash’ indicator light is flashing on Aquarius models Different load types need different drying timesBefore calling the Service Centre ServiceSpare Parts

WD645, WD440, WD640, WD420 specifications

The Hotpoint WD420, WD640, WD440, and WD645 are an impressive range of washer-dryers designed to meet the diverse needs of modern households. Each model is characterized by its combination of efficient washing and drying capabilities, making them ideal for those who value convenience without sacrificing performance.

The Hotpoint WD420, known for its compact design, is perfect for smaller living spaces. It boasts a 6 kg washing capacity and a 5 kg drying capacity, making it sufficient for individuals or small families. Its 1200 rpm spin speed ensures efficient water extraction, reducing drying time significantly. This model features the ‘Anti-Ageing’ program, which uses lower temperature washes and spins to help protect delicate fabrics, prolonging their lifespan.

In contrast, the WD640 offers a more extensive capacity, with a 7 kg washing and a 5 kg drying capability. This model introduces advanced features such as the ‘Rapid Wash’ program, which allows users to wash small loads in just 30 minutes - ideal for those busy days when time is of the essence. It also includes a sensor drying function, which adjusts the drying time based on the moisture levels in the drum, ensuring energy efficiency and protecting clothes from overdrying.

The WD440 enhances the drying experience with its 6 kg washing and 5 kg drying capacities. A notable characteristic of this model is its ‘Cotton’ cycle, designed specifically to handle cotton fabrics like shirts and bed linens, providing optimal cleaning and drying. Additionally, the model includes a delay timer, allowing users to set the appliance to start at their convenience, a great feature for balancing busy schedules.

Finally, the WD645 epitomizes versatility, featuring a larger washing capacity of 8 kg and a drying capacity of 6 kg. It comes equipped with Smart Technology, which utilizes sensors to monitor load size and optimize wash cycles for the best performance. The model also features a special ‘Wool’ cycle, ensuring that woolen items are washed gently, thus preventing any shrinkage or damage.

Together, these Hotpoint washer-dryer models combine innovative technologies with user-friendly features such as various wash programs, energy efficiency, and compact designs. They truly cater to the needs of contemporary life, making laundry tasks simpler and more efficient, benefiting households of all sizes and lifestyles.
Top Page Image Contents