Bosch Appliances V20-UL Electrical Connection Integrated Socket, Exhaust Air Connection, Must

Electrical

connection

Integrated

socket

d WARNING

d

d CAUTION

d

This appliance is equipped with a

1.

To reduce the risk of fire,

this

socket for connecting a washer

Connect

to

individual

Brunch

without

fuses.

Only

the listed

dryer

MUST

BE

EXHAUSTED

washer

may

be

connected. For

all

OUTDOORS.

Circuit.

other

connections

Bosch

will

2.

To reduce the

risk

of

fire,

do

Do not use an adapter.

assume

no

liability.

not use the ductwork longer

Do

not

use

an

extension cord.

d CAUTION

d

than

recommended.

Do

not

remove

ground

prong.

3.

DO NOT use a plastic or

Use

copper

conductors only.

non?metal

duct

with

this

dryer.

4.

DO

NOT

use

a

duct

smaller

Your

dryer

comes

with a power

Connect

to

a

30

A

minimum

than

4

inches

in

diameter.

supply

cord:

individual

branch

circuit,

fused

at

5.

DO NOT use exhaust hoods

-

UL

listed

in

the USA,

30

A

maximum.

with

magnetic

latches.

-

CSA

listed

in

Canada.

Use

receptable

only

for:

6.

DO

NOT

exhaust

the

dryer

into

When

installing

the

receptacle for

208

-

240 VAC

60

Hz

11

A

a chimney,

furnace

cold

air

duct,

attic,

crawl

space,

or

any

the

dryer cord,

ensure that the

washer:

WFR2460UC,

other ductwork

used for

power

supply

cord

is

accessible

WFL2060UC.

venting.

when

the

dryer

is

in

the installed

7.

DO

NOT

install

a flexible duct

position.

Exhaust

air

connection

in an enclosed

wall, ceiling

or

The

power

cord

should

only be

You

can

use

the exhaust

air

set

floor.

replaced

by a

qualified person.

8.

DO

NOT

crush

or

kink

the

Use a

4?wire

power

supply cord.

which

can be

obtained from

duct.

customer

service

or

your

local

Grounding

instruction

9. Do clean

and

inspect

the

dealer WTZ1130(

).

The

dryer

comes

with

a

cord which

any

products

which

are

exhaust

system

on

a

regular

has

an

equipment

grounding

Also

basis; at

least

once a

year.

commercially available can be used

conductor and a grounding plug.

10.

The

exhaust

duct

must

The plug must be plugged into anfor the exhaust air duct:

terminate in a manner to

appropriate outlet which has been

-

flexible

tubes,

prevent back drafts or entry of

properly

installed

and

grounded in

-

galvanised

sheet

metal

ducts

or

birds

or

other

wildlife.

accordance

with

all

local

tubes,

The Bosch dryers are intended to

regulations

and

ordinances.

be

vented

outdoors.

To

prevent

-

connection,

transfer

and

flatbuild?up

of

moisture

and

d CAUTION

d

by?pass

adapters for use

in

duct

or

tubular

ducting

accumulation of lint indoors, as well

as to maintain maximum drying

Improper

connection

of

the

systems,

efficiency, it is recommended that

equipment grounding

conductor

-

wall

boxes

for

ventilation

into

the dryer is vented outdoors.

may result in electric shock.

the

open

air

or into

an

air

shaft,

Have

the

appliance checked by

-

adapters

for

rectangular ducts,

i

Position

the

exhaust

air

duct

so

a qualified

electrician

or

service

that there is no counter?

technician

if

you are

in

doubt as -

rectangular

ducts or plastic

to

whether

the

dryer

has been

tubesone?way

flap.

pressure

(e.g. from

wind)

on

the

exhaust

outlet.

properly

grounded.

d CAUTION

d

All materials must be heat?resistant up to 80 °C and humidity?resistant.

8