Blomberg TKF 8439 A manual Installation

Page 8

3Installation

Refer to the nearest Authorised Service Agent for installation of your product.

CPreparation of location and electrical installation for the product is under customer’s responsibility.

BInstallation and electrical connections

must be carried out by a qualified personnel.

A Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety.

Appropriate installation location

Install the product in an environment which has no risk of freezing and is in a stable and level position.

Operate your product in a well ventilated, dust-free environment.

Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden bands.

Do not place your product on a long pile rug or on similar surfaces.

Do not install the product behind a door with a lock, sliding door or a hinged door which can strike the product.

Once the product is installed, it should stay at the same place where its connections have been made. When installing the product, make sure that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.

B Do not place the product on top of the power cable.

Keep at least 1.5 cm distance to walls of other furniture.

Removing the transportation safety assembly

ARemove the transportation safety assembly before using the product for the first time.

1.Open the loading door.

2.There is a nylon bag inside the drum that contains a piece of styrofoam. Hold it from its section marked with XX.

3.Pull the nylon towards yourself and remove the transportation safety assembly.

8

AMake sure that you have removed the transportation safety assembly (nylon+styrofoam pieces) before using the product for the first time. Do not leave any items inside the drum.

Under counter installation

It should never be operated without the top trim.

Leave at least 3 cm of space between the side and rear walls of the product and the walls of the counter/cupboard when installing your product under a counter or in a cupboard.

Mounting over a washing machine

A fitting device should be used between the two machines when installing above a washing machine. The bracket must be installed by the Authorised Service Agent.

Place the product on a firm floor. If it will be placed on top of a washing machine, the approximate weight of both machines may reach 180 kg when they are full. Therefore, the floor must be capable of carrying the load on it!

The bracket can be supplied from the Authorised Service Agent.

Connection to water drain;

In products equipped with a condenser unit the water accumulated during the drying cycle is collected in the water tank. You should drain the accumulated water after each washing cycle.

You can directly send the accumulated water out through the water drain hose supplied with the machine instead of periodically draining the water collected in the water tank.

EN

Image 8
Contents TKF 8439 a Dryer Read this manual prior to initial operation of the product Table of Contents Your Dryer OverviewTechnical Specifications Important safety instructions General safetyChildren’s safety Intended useInstallation Adjusting the feet First useDisposing of packaging material Transportation of the machineDisposing of the old machine Washer/dryer combination Electrical requirementsFitting a different plug Initial preparations for drying Things to be done for energy savingLaundry suitable for drying in the machine Laundry unsuitable for drying in the machinePreparing laundry for drying Correct load capacityLoading Selecting a Programme and OperatingYour Machine Control panelPreparing the machine Programme selectionTime display ViscoseProgramme selection and consumption table Programme table Drying time Minutes Cottons / ColoredsAuxiliary function Drying degreeAnti-creasing Changing the contrastTime delay Changing the delay timeCancelling the time delay Starting the programmeChild-proof lock Adding/removing laundry in standby modeChanging the programme after the programme has started Ending the programme through cancelling End of programmeWater tank Maintenance and cleaningFilter Cartridge / Door Inner Surface For the condenser Suggested solutions for problems Guarantee Service Blomberg, 36-38 Caxton Way, Watford Hertfordshire, WD18 8UF