Sterling SCD 10 specifications Making Electrical Connections, Making Compressed Air Connections

Page 17

3-4 Making Electrical Connections

The serial tag lists voltage, phase, and amp draw information. Line voltage must be within plus or minus ten percent of the voltage listed on the serial tag, or damage may occur. Never supply any voltage other than what the dryer is configured for.

Fulfill all national, state, and local safety and electrical code requirements. A qualified electrician should make all electrical connections.

Connect main power to the dryer. Install a fused disconnect with a lockout feature in the power main leading to the dryer. The power drop must include a ground wire. Make sure all electrical connections are tight.

Note: Due to variances in 220-240 V connections, customers must supply the plug for these dryer models.

3-5 Making Compressed Air Connections

The compressed air supply must be regulated to 80 PSI (5.5 bars). Low air pressure will create poor drying performance. If the pressure in the system drops below 35 PSI, the alarm light will activate and the process heater and solenoid valve will shut off.

Note: For maximum drying efficiency, we recommend a refrigerated compressed air connection. Not using refrigerated compressed air (to provide pre-conditioned compressed air to this unit) will affect drying performance and material drying capabilities.

To achieve the lowest possible dew points, an optional remote-mount membrane dryer assembly is available. See Section 2-7 on page 10 for more information about the remote- mount membrane dryer assembly.

Connect a minimum of 3/8” (9 mm) air line to the top of the filter regulator. Compressed air must be clean, dry, and free of oil. A shut-off is recommended for your in-plant air supply. In-line filters can handle small amounts of moisture; in-line desiccant filters or packed beds of granular absorbing polymer can remove oil mist and condensed oil.

10 CFM Compressed Air Dryer

Chapter 3: Installation

17 of 30

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SCD 10 Compressed Air Dryer Shipping Info Table of Contents Appendix Safety Symbols Used in this Manual SafetyHow to Use This Manual Responsibility General Safety RegulationsPage Functional Description Typical Features and ComponentsModels Covered in This Manual General DescriptionDrying Hopper Air Trap Safety FeaturesRemote Membrane Dryer for Low-Dew point Operation Optional Remote-Mount Membrane Dryer Airflow SchematicMicroprocessor Controller Microprocessor ControlsButton or Indicator Function Identifying the Controller’s Buttons and IndicatorsParameter Function Understanding the Controller’s ParametersRestoring Factory Default Settings Uncrating the Equipment InstallationConnecting a Hopper-Mount Dryer to a Hopper Floor-Mount Configuration Connecting a Floor-Mount Dryer to a Hopper OptionalMaking Compressed Air Connections Making Electrical ConnectionsMembrane Dryer Assembly Installing the Remote-Mount Membrane Dryer OptionalOperation Auto-tuning the DryerSetting the Alarm Value Shut-down Start-upCleaning and Replacing the Filters MaintenancePreventative Maintenance Schedule Replacing the Fuse Outside of the Cabinet Problem Possible Cause Possible Remedy TroubleshootingProblem Possible Cause Possible Remedy Appendix Warranty ReturnsReturned Material Policy Credit ReturnsTechnical Assistance Service DepartmentParts Department Sales DepartmentTechnical Specifications Dryer Operating Parameters Dimensions Quantity Description Spare Parts List

SCD 10 specifications

The Sterling SCD 10 is a sophisticated digital aggregation and communication platform designed primarily for industrial applications. This innovative system provides a comprehensive set of features and technologies that revolutionize data management and communication across various sectors.

At its core, the Sterling SCD 10 excels in data aggregation, seamlessly integrating information from multiple sources and sensory inputs. This capability allows organizations to consolidate their operational data into a single, coherent platform, enabling more informed decision-making processes. By providing real-time insights, the Sterling SCD 10 enhances visibility into system performance, resource utilization, and operational efficiency.

One of the standout features of the Sterling SCD 10 is its advanced communication capabilities. The platform supports multiple communication protocols, ensuring compatibility with a diverse range of devices and networks. This flexibility is crucial for industries that rely on various technologies and systems. Moreover, the Sterling SCD 10 is designed to work harmoniously with both legacy systems and new technologies, facilitating smoother upgrades and integrations.

The Sterling SCD 10 also incorporates robust data security measures to protect sensitive information. With features like encrypted data transmission and secure access controls, the platform prioritizes the integrity and confidentiality of the data being processed. This is particularly important in industries that deal with regulatory compliance and sensitive operational data.

In terms of user experience, the Sterling SCD 10 boasts an intuitive interface that simplifies navigation and data visualization. Users can easily monitor system performance, analyze trends, and generate reports, making it accessible for personnel at various skill levels. Customizable dashboards and analytics tools allow users to tailor their views and gain insights that matter most to them.

Furthermore, the Sterling SCD 10 is highly scalable, making it suitable for businesses of all sizes. Whether a small enterprise or a large corporation, users can scale the platform's capabilities according to their evolving needs. This scalability is backed by a robust cloud infrastructure that ensures high availability and reliability.

Overall, the Sterling SCD 10 stands out in the arena of digital communication and data aggregation with its rich feature set, advanced technologies, and a commitment to security and user-friendly operation. Its ability to integrate seamlessly into existing frameworks while providing vital operational insights positions it as a pivotal tool for modern industries looking to enhance their efficiency and innovation.
Top Page Image Contents