ADC HBG76 Non-Coin Models, Shutdown Instructions, Service/Parts Information, Warranty Information

Page 18

Non-Coin Models

Microprocessor Controller (Computer)

The L.E.D. display reads “READY” (no cycle in progress).

Press the letter on the keypad corresponding to the cycle desired (e.g. key “D”).

The dryer will then start (i.e. blower, tumbler, and heat).

The L.E.D. display will read MANUAL DRYING CYCLE D,

___MIN REMAIN.

Note: The dryer can be stopped at any time by pressing the “STOP/CLEAR” key, at this time the dryer will go into a cycle pause. If the “STOP/CLEAR” key is pressed again at this point, the cycle that was in progress will be cancelled and returned to the “READY” state.

When the programmed drying time has expired, the non- coin microprocessor controller (computer) will proceed into the Cool Down Cycle.

Once the Cool Down Cycle begins at the end of the heat cycle, the L.E.D. display will read COOL DOWN TEMP __/__ MINUTES remaining. At the end of the heat cycle, the dryer will shut off the heat and continue the fan and tumbler until the Cool Down Time or temperature is reached.

Shutdown Instructions _______________

If the dryer is to be shutdown (taken out of service) for a period of time, the following must be performed:

Discontinue power to the dryer either at the external disconnect switch or the circuit breaker.

Discontinue the heat supply:

Gas Models – Discontinue the gas supply. Shut off external gas supply shutoff valve.

Shut off internal gas supply shutoff valve located in the gas valve burner area.

Steam Models – Discontinue the steam supply. Shut off external (location furnished) shutoff valves.

Service/Parts Information ____________

Service

Service must be performed by a qualified trained technician. If service is required, contact the reseller from whom the equipment was purchased. If the reseller cannot be contacted or is unknown, contact the Service Department for a reseller in your area.

Note: When contacting the Service Department, be sure to give them the correct model number and serial number so that your inquiry is handled in an expeditious manner.

Parts

Replacement parts should be purchased from the reseller from whom the equipment was purchased. If the reseller cannot be contacted or is unknown, contact the Parts Department for a reseller in your area. Parts may also be purchased directly from the factory by calling the Parts Department at +1 (508) 678-9000 or you may FAX in your order at +1 (508) 678-9447.

Note: When ordering replacement parts from the reseller or the manufacturer, be sure to give them the correct model number and serial number so that your parts order can be processed in an expeditious manner.

Warranty Information _________________

Returning Warranty Cards

Before any dryer leaves the factory test area, a warranty card is placed on the inside of the main door glass. These warranty cards are intended to serve the customer where we record the individual installation date and warranty information to better serve you should you file a warranty claim.

If a warranty card did not come with your dryer, contact the Warranty Department or the Service Department at +1 (508) 678-9000.

Important: A separate warranty card must be completed and returned for each individual dryer.

Note: Be sure to include the installation date when returning the warranty card(s).

Warranty

For a copy of the commercial warranty covering your particular dryer(s), contact the reseller from whom you purchased the equipment and request a dryer warranty form. If the reseller cannot be contacted or is unknown, warranty information can be obtained from the factory by contacting the Warranty Department at +1 (508) 678-9000.

Note: Whenever contacting the factory for warranty information, be sure to have the dryer’s model number and serial number available so that your inquiry can be handled in an expeditious manner.

Returning Warranty Parts

All dryer or parts warranty claims or inquiries should be addressed to the Warranty Parts Department. To expedite processing, the following procedures must be followed:

No parts are to be returned without prior written authorization R.M.A. from the factory.

Note: An R.M.A. is valid for only 30 days from date of issue.

The R.M.A. issued by the factory, as well as any other correspondence pertaining to the returned part(s), must be included inside the package with the failed merchandise.

Each part must be tagged with the following information:

Model number and serial number of the dryer from which part was removed.

Nature of failure (be specific). Date of dryer installation. Date of part failure.

Specify whether the part(s) being returned is for a credit, replacement, or a refund.

Note: If a part is marked for a credit or a refund, the invoice number covering the purchase of the replacement part must be provided.

18

American Dryer Corp.

113615 -2

Image 18
Contents HBG76 American Dryer CorporationHBG76 Table of Contents Safety Precautions What To Do If You Smell GasCE Only Specifications 69.37 cmSpecifications Location Requirements Installation ProceduresUnpacking/Setting Up Dryer Enclosure RequirementsFresh Air Supply Requirements Exhaust RequirementsHorizontal Venting Outside Ductwork ProtectionSingle Dryer Venting Vertical VentingElectrical Service Specifications Gas and Steam Models Only Electrical InformationElectrical Requirements Grounding Single-Phase 1ø Wiring Connections/HookupElectric Models Only Electrical ConnectionsGas Information CE and Australian DryersHeat Input/Gas Consumption/Orifice Injector Data Piping/ConnectionsSteam Information Gas Pressure TestingGas Pressure Test Procedure Steam Coil pH LevelWater Information Preoperational Instructions Preparation for Operation/Start-UpPreoperational Test Coin ModelsNon-Coin Models Service/Parts InformationWarranty Information Shutdown InstructionsRoutine Maintenance Data Label Information Standard Label AGA Label CE Label113615 ADC Part No 10/14/08

HBG76 specifications

The ADC HBG76 is a state-of-the-art device designed for high-performance data acquisition and processing. It is primarily aimed at various applications in industries such as telecommunications, aerospace, military, and industrial automation. The HBG76's advanced features, robust technologies, and exceptional characteristics make it a standout choice for professionals requiring precise and reliable data handling.

One of the hallmark features of the HBG76 is its high-speed sampling capabilities. The ADC can handle sample rates exceeding 1 GSPS (giga samples per second), enabling it to capture rapid signal dynamics with exceptional fidelity. This capability is particularly valuable in applications where timing is crucial, such as radar systems or high-frequency trading in finance.

The HBG76 incorporates cutting-edge analog-to-digital conversion technology, ensuring that the signal integrity is maintained throughout the conversion process. With a resolution of up to 16 bits, the ADC delivers impressive accuracy and detail, facilitating high-quality signal representation. This feature is essential for applications requiring precise measurement and analysis of data.

Another significant aspect of the HBG76 is its versatility in connectivity options. The device supports various communication interfaces, including USB, Ethernet, and SPI, making it compatible with a wide range of systems. This flexibility allows users to integrate the ADC seamlessly into existing hardware setups, enhancing overall efficiency and ease of use.

In terms of power efficiency, the HBG76 is designed with advanced low-power technologies that optimize its energy consumption without compromising performance. This feature is particularly beneficial for battery-operated devices and remote applications where power availability may be limited.

The robust design of the HBG76 ensures longevity and reliability in demanding environments. Its rugged casing provides protection against dust, moisture, and temperature extremes, making it suitable for outdoor use and harsh industrial settings.

Overall, the ADC HBG76 stands out as a powerful tool for data acquisition and processing, boasting high-speed sampling, excellent resolution, versatile connectivity, energy efficiency, and durability. Whether in research laboratories, industrial monitoring, or advanced telecommunications systems, the HBG76 is engineered to meet the evolving needs of modern applications, driving innovation across diverse sectors.