Maytag W10155112A, W10155111A Make Gas Connection, Connect Vent, Level Dryer, For mobile home use

Page 12

2.Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on the cardboard. See illustration.

A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown is a recommended connection. Your connection may be different, according to the supply line type, size and location.

3.

Examine the leveling legs. Find the diamond marking.

4.

Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the

A

B

D

C

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor.

Mobile home installations require a Mobile Home Installation Kit. See “Tools and Parts” section for information on ordering.

Make Gas Connection

1.Remove the red cap from the gas pipe.

2.Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound on the threads of all non-flared male fittings. If flexible metal tubing is used, be sure there are no kinks.

A B

A. Flared male fitting

B. Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. Do not use TEFLON®† tape.

®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

A. ³⁄₈" flexible gas connector

B. ³⁄₈" dryer pipe

C. ³⁄₈" to ³⁄₈" pipe elbow

D. ³⁄₈" pipe-to-flare adapter fitting

3.Open the shutoff valve in the supply line. The valve is open when the handle is parallel to the gas pipe.

A

B

A. Closed valve

B. Open valve

4.Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.

Connect Vent

1.Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2.Move dryer into its final location. Do not crush or kink vent.

3.(On gas models) Check that there are no kinks in the flexible gas line.

4.Once the exhaust vent connection is made, remove the corner posts and cardboard.

Level Dryer

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

12

Image 12
Contents GAS Dryer W10155111ATable of Contents Dryer SafetyWhat to do if YOU Smell GAS Important Safety Instructions Installation Instructions Tools and PartsLocation Requirements Installation Clearances Mobile Home Additional Installation RequirementsDryer Dimensions Mobile home installations requireElectrical Requirements Gas Supply RequirementsGas Type Gas supply lineGas supply pressure testing Venting RequirementsGas supply connection requirements Burner input requirementsIf using an existing vent system If this is a new vent system Vent materialOptional exhaust installations Alternate installations for close clearancesPlan Vent System Install Vent System Install Leveling LegsVent system chart Special provisions for mobile home installationsMake Gas Connection Connect VentLevel Dryer For mobile home useComplete Installation If the dryer will not start, check the followingDryer USE Starting Your DryerStopping and Restarting How Sensor Dry WorksCleaning the Dryer Location Cleaning the Lint ScreenEvery Load Cleaning Dryer CareCleaning the Dryer Interior Removing Accumulated LintVacation and Moving Care Changing the Drum LightTroubleshooting Dryer OperationDryer Results Cycle time too short Lint on loadStains on load or drum Loads are wrinkledAssistance or Service AccessoriesIf you need replacement parts U.S.AMaytag Corporation Major Appliance Warranty W10155111A SP PN W10155112A

W10155112A, W10155111A specifications

Maytag is a well-known brand in the appliance industry, recognized for its commitment to quality, performance, and innovation. Among its extensive lineup, the Maytag W10155111A and W10155112A stand out as reliable options for consumers in need of efficient appliance solutions. These products are designed to enhance home efficiency while providing durability and functionality.

The Maytag W10155111A is a replacement part that is primarily used in Maytag washers, specifically the tub seal. It ensures that the washing machine operates smoothly by preventing water leaks from the tub during the washing cycle. This component is crucial for maintaining the integrity of the appliance, leading to better washing performance and preventing potential water damage to the surrounding areas.

On the other hand, the W10155112A is another essential component that functions as a washer. It is designed to work in conjunction with various washing machines to provide optimal performance. This part is engineered to withstand high-pressure conditions and is made from high-quality materials that ensure longevity. The combination of these components contributes to more efficient washing cycles, reducing water usage and energy consumption, thereby offering environmental benefits alongside practicality.

A notable feature of both components is their compatibility with a wide range of Maytag washer models, making them versatile choices for homeowners. Additionally, their easy installation process allows users to replace worn-out parts with minimal effort, saving time and repair costs. Maintenance is also simplified, as these parts are designed for easy access and replacement.

In terms of technology, Maytag emphasizes durability and reliability. The materials used in the manufacturing of these components are carefully selected to withstand the rigors of daily use, ensuring that they can handle a variety of laundry loads without compromising performance.

Overall, the Maytag W10155111A and W10155112A exemplify the brand's dedication to quality and consumer satisfaction. These components not only enhance the performance of Maytag washing machines but also contribute to the long-term efficiency and durability of the appliance. With their ease of installation and reliable performance, these parts are ideal for anyone looking to maintain their washing machine in prime condition. Investing in these components means choosing reliability and efficiency for a modern laundry experience.