Iii, Panel D | Whirlpool 3389591 manual

IO In Before attaching water inlet hoses, run water through both faucets into a bucket. This will get

rid of particles in water lines that might clog hoses. Mark

which is the hot water faucet.

11 WAttach bottom hose (inlet marked “H”) to hot water faucet. Attach top hose (inlet marked ‘C”) to cold water faucet. Tighten the coupling to the faucet by hand. Use pliers to make final two-thirds turn.

Move washer/dryer to its permanent location. Remove cardboard from under washer/dryer.

12 n Tilt washer/drver				forward
raising back legs 1 inch ‘off of floor to
adjust rear, self-leveling			legs. Gently
lower washer/dryer		to floor. Check
levelness of	the washer/dryer			by	placing
a carpenter’s	level	on	top of the washer,
first side to side; then front to back. If						-
washer/dryer	is level,		go to	Step	14.

’	Insert corner posts		6 inches
,	from lefi leg. Do Not insert
,	corner PO.& in the center of
	corner PO.& in the center of
	the washer/dryer.
13 n If it is not level,		carefullv		tilt
washer/dryer	backward.until		front	of
washer/dryer	is 3-4 inches	off	of floor.

Insert 4 corner posts under washer/dryer about 6 inches from the left leg. Loosen nuts on each front leg. Adjust the front legs up or down. Tilt washer/dryer backward and remove corner posts. Gently lower the washer/dryer to the floor. Repeat Step 12. If it is still not level, repeat Step 13 and then Step 12 until washer/dryer is level.

14 n When washer/drver is level, use wrench to turn nuts on front legs up” tightly against washer/dryer base. If nuts are not tight against washer/dryer base, the washer/dryer may vibrate.

Property Damage

Secure the drain hose to the tub or standpipe with the shipping strap removed from the back of the washer.

Failure to properly secure drain hose could result in water damage.

n Measure and mark a point

approximately 15 inches from the plug end of the shipping strap. Cut the shipping strap at this point.

Check that hose is not twisted or kinked and is securely in place.

stiap strbp strbp

Put “hook” end of drain hose in tub or standpipe. Tightly wrap the shipping strap around the drain hose and tub or standpipe or inlet hose as shown in Figures A-C. Push plug into the nearest hole in the shipping strap.

If drain hose cannot be strapped in place, it must be cut exactly to length so the “hook” end is held tightly over the edge of the tub or standpipe.

If a longer drain hose is needed, drain hose (Part

No. 388423) and ML hose extension

kit (Part No.

285442) are available from a

Whirlpool-authorized parts distributors. If drain hose must be shortened, use hose kit (Part No. 285442).

Note: If washer/dryer is moved to adjust drain hose, the washer/dryer must be leveled again. Repeat Steps 12- 14. Place cardboard under the washer/dryer and carefully move washer/dryer to avoid damaging floor covering.

III I

16 n If vou did not remove the access panel in Step 8, remove three Phillips-head screws and one bumper, located at the top of the access panel. Set the panel, screws and bumper aside.

17 n Determine the lenath of exhaust

duct that is needed to con&t the dryer to the exhaust hood. (See “Exhaust requirements,” Panel B.) Connect exhaust duct to the washer/dryer and then to the exhaust hood.

/YIP4/’

18 n Use duct tape to seal all ioints

in exhaust duct. Use caulking ’ compound to seal exterior wall opening around exhaust duct hood.

19 n CHECK ELECTRICAL REQUIREMENTS. BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD. Check the Installation Instructions to see that you have completed each step. Complete any missed steps before you continue.

n Check that all parts are now installed. (See parts list, Panel C.) If there is an extra part, go back through steps to see which step was skipped.

21 n Check that you removed all the shipping pieces including the shipping strap with its 2 cotterpins and plug. Dispose of all materials in proper manner.

If you do not remove the shipping strap, your washer/dryer may “walk” away from its location.

	adjustable
Phillips screwdriver	wrench (tw

your tools

23 WTurn on water faucets and check for leaks. Tighten couplings if there is leaking. Do Not overtighten; this could cause damage to faucet.

24 n Replace access panel. Be sure to tighten the three Phillips-head screws at the top of the access panel. Replace the bumper under the center screw.

Guide to fully understand your new washer/dryer. Open dryer door. Check to be sure lint screen is in its proper position. Wipe out drum.

grounded outlet. Now start the washer and allow it to complete the regular cycle.

27 WStart dryer and allow it to complete a full heat cycle to make sure it is working properly.

successfully installed your new, Whirlpool washer/dryer.

your new washer/dryer, read your Whirlpool Use and Care Guide.

Congratulations!

Keep Installation Instructions nearby where you can refer to them. They’ll make reinstalling your Whirlpool washer/dryer in another home as easy as

the first installation.

Panel D

3389591 specifications

The Whirlpool 3389591 is a versatile and essential component for those seeking to maintain or enhance their home appliance experience. Specifically designed for use in various Whirlpool dryers, this temperature sensor plays a crucial role in ensuring optimal operation. One of its primary functions is to regulate the dryer’s temperature, ensuring that clothes are dried efficiently while preventing overheating, which can lead to damage or fire hazards.

One of the main features of the Whirlpool 3389591 is its compatibility. It is designed to work seamlessly with multiple models, making it a go-to replacement part for numerous Whirlpool dryer users. This versatility addresses the common challenge of finding the right part for specific appliance models, providing a reliable solution for maintenance needs. Additionally, the sensor is engineered for easy installation, allowing homeowners to replace it without requiring extensive technical knowledge or specialized tools. This user-friendly feature is a significant advantage for those who prefer DIY repairs.

In terms of technology, the Whirlpool 3389591 utilizes advanced thermal sensing capabilities. It is designed to provide precise temperature readings, crucial for effective moisture removal from clothing during drying cycles. This technology not only enhances the efficiency of the drying process but also contributes to energy savings. By maintaining an appropriate temperature, the sensor ensures that the dryer operates within its optimal range, ultimately prolonging the lifespan of the appliance.

Furthermore, the characteristics of the Whirlpool 3389591 highlight its durability and reliability. Constructed with high-quality materials, this temperature sensor is built to withstand the rigors of regular use. Its robustness ensures that it can function well under various operating conditions, making it a dependable choice for long-term use.

Overall, the Whirlpool 3389591 temperature sensor is a critical component that enhances the performance of Whirlpool dryers. With its compatibility, ease of installation, advanced technology, and durable construction, it represents a smart investment for homeowners looking to ensure their appliances operate efficiently and safely. By keeping an eye on such essential parts, users can enjoy a more reliable and effective drying experience in their laundry routines.