Humminbird 947C 3D Sonar X-PRESS Menu, Highlight Split Position on the 3D Sonar X-Press Menu

Page 55

531374-1_A - 947 Man.qxd 2/15/2005 7:54 PM Page 55

3D SONAR X-PRESS™ MENU

(3D Sonar Views only)

The 3D Sonar X-Press™ Menu provides access to the settings most frequently used. Press the MENU key once while in any of the 3D Sonar Views to access the 3D Sonar X-Press™ Menu.

NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode or whether a 2D or a 3D View is currently displayed/active.

3D Sonar X-Press™ Menu

ACTIVE SIDE

Active Side allows you to select which side of a Combo View will be active; key presses will only affect the active side of the screen. When a menu is displayed, the non-active side of the screen will be grayed out; at any other time, a green arrow will point to the active side. Combo Views usually display sonar on the left, with charts or Bird’s Eye usually on the right. The Active Side menu choice is only available when a Combo View is active.

To select the Active Side:

1.Highlight Active Side on the 3D Sonar X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to change which side is active. (Left, Right, Default = Left, or Sonar).

SPLIT POSITION

Split Position allows you to adjust what percentage of the screen is taken up by the left side of any Combo View; each view may be adjusted independently; you must be in a specific view to adjust the screen size for that view. The number setting indicates the percentage taken up by the left side of the Combo View; selecting Left sets the left side of the screen to its smallest setting. The Split Position menu choice is only available when a Combo View is active.

To Adjust Split Screen Position

1.Highlight Split Position on the 3D Sonar X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to change the size of the left side of a Combo View. (Left,30, 40, 50, 60, 70, Right, Default = 50)

50

Image 55

Contents 531374-1A 947 Man.qxd 2/15/2005 752 PM Thank You Table of Contents Navigation X-Press Menu Menu System Start-Up Options Menu2D Sonar X-Press Menu 3D Sonar X-Press MenuViews Menu Tab Accessories Menu Tab Troubleshooting Chart Menu TabAlarms Menu Tab Setup Menu Tab2D Sonar Series IntroductionHOW the 900 Series Works 3D SonarMULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot 900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory BusBasic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control HeadIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer InstallationTo determine transducer mounting location Transom Transducer InstallationStepped Hull Attaching the Bracket To mount the transducer bracket to the boatTo attach the pivot to the transducer But do not completely tightenTo adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Routing the Cable To route the transom transducer cableReassemble Fully tightenedTrial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Transducer Mounted Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is markedTrolling Motor Transducer Installation Test and Finish the Transducer InstallationFollow these steps to stem mount the GPS receiver GPS Receiver InstallationIf you have… Then use Hand-tighten onlyAccess Under Mounting Location Access Under Mounting LocationTo the cable as shown Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationRouting the cable to the control head Install the temperature probe accessoryTo test the installation Testing the System InstallationSeries 947c 3D Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the 3D Sonar DisplayBait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar DisplayBottom Presentation Real Time Sonar RTS WindowMenu KEY POWER/LIGHT KEYKEY Functions View KEYInfo KEY View Preset KeysWAY Cursor Control KEY Exit KEYViews MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBird’s Eye View Beam Sonar ViewBIRD’S EYE View Beam Sonar ViewChart View with Active Cursor CHART/BIRD’S EYE Combo ViewChart View Chart/Bird’s Eye Combo View with Active CursorCHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Chart View with GridEDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Advanced Mode Sonar Tab, Normal ModeStart-Up Options Menu Exit Normal operation by powering your 900 Series offSTART-UP Options Menu Normal OperationSystem Status Self Test Accessory Test GPS Diagnostic ViewExit the Simulator by powering your 900 Series off SimulatorGPS Diagnostic View Accessory TestGPS Diagnostic View Accessory Test ScreenSplit Position To Adjust Split Screen Position2D Sonar X-PRESS Menu Active SideUpper Range To adjust the SensitivityTo adjust the Upper Range SensitivityLower Range Chart SpeedBottom Lock To change the 2D/3D Priority To adjust the Bottom RangeBottom Range 2D/3D PriorityHighlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range 3D History Reset 3D ViewTo adjust the 3D History To Reset 3D ViewNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuSkip Next Waypoint Save Current TrackClear Current Track Save Current RouteRemove Target Cancel NavigationRemove Grid 3D Frame Style Sonar Menu TAB2D Sonar Colors 3D Bottom StyleTo set Fish ID+ 2D Beam SelectFish ID+ To change Beam SelectFish ID Sensitivity To change the Fish ID Sensitivity settingTo change the RTS Window setting To change the Fish ID 3D Reference settingDepth Lines Bottom ViewZoom Width KHZ SensitivityNoise Filter To change the Noise Filter settingTo change the Max Depth setting Surface ClutterWater Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints North Reference To change the Chart Orientation settingTo change the North Reference setting RoutesMAP Datum Trolling Grid RotationTrackpoint Interval Track MIN DistanceTo Export All Navigation Data Chart Menu TABExport ALL NAV Data Delete ALL NAV DataSpot Soundings Chart Detail LevelMAP Borders LAT/LON GridSET MAP Offset Shaded DepthClear MAP Offset To change the Depth Alarm setting Alarms Menu TABDepth Alarm Fish ID AlarmTemp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp settingLanguage User ModeUnits Distance Units SpeedRestore Defaults Triplog ResetSelect Readouts To Select Readouts Default Sonar View Customized Sonar ViewDaylight Saving Time Depth OffsetTemp Offset Local Time ZoneNmea Output Position FormatTime Format Date FormatTo turn Sonar on or off SonarViews Menu TAB To turn Nmea Output on or offTroubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display ProblemsBoat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appearsHumminbird Service Policy Year Limited WarrantySeries Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Operating Frequency SpecificationsAppendix a Contact Humminbird