Humminbird 947C manual Export ALL NAV Data, Delete ALL NAV Data, Chart Menu TAB

Page 70

531374-1_A - 947 Man.qxd 2/15/2005 7:54 PM Page 70

EXPORT ALL NAV DATA

(Advanced)

Export All Nav Data allows you to export all saved Tracks, Waypoints and Routes to an

MMC/SD card.

To Export All Navigation Data:

1.Make sure you are in Advanced User Mode, and that an optional-purchase MMC/SD card is installed in the slot, then highlight Export All Nav Data on the Navigation main menu.

2.Use the RIGHT 4-WAY Cursor Control key to export all navigation data.

Chart Menu

DELETE ALL NAV DATA

(Advanced)

Delete All Nav Data allows you to delete all saved Tracks, Waypoints and Routes. This menu choice should be used with caution.

To Delete All Navigation Data:

1.Make sure you are in Advanced User Mode, then highlight Delete All Nav Data on the Navigation main menu.

2.Use the RIGHT 4-WAY Cursor Control key to delete all navigation data.

CHART MENU TAB

Press the MENU key twice to access the Main Menu System and then press the RIGHT Cursor key to select the Chart tab.

NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode.

65

Image 70

Contents 531374-1A 947 Man.qxd 2/15/2005 752 PM Thank You Table of Contents 3D Sonar X-Press Menu Menu System Start-Up Options Menu2D Sonar X-Press Menu Navigation X-Press MenuSetup Menu Tab Chart Menu TabAlarms Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting3D Sonar Series IntroductionHOW the 900 Series Works 2D SonarMULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot Accessory Bus Accessory BUSInstallation Overview 900 Series has a wide variety of configurationsBasic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Plug Cable Connector Assembly to Back of Control Head Screws providedIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Transducer Installation Connecting the Control Head Power Cable to the BoatTo determine transducer mounting location Transom Transducer InstallationStepped Hull But do not completely tighten To mount the transducer bracket to the boatTo attach the pivot to the transducer Attaching the BracketTo adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Fully tightened To route the transom transducer cableReassemble Routing the CableTrial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Make sure the position of the transducer is marked Permanently mount the transducerRoute the cable Transducer Mounted Inside the HullTest and Finish the Transducer Installation Trolling Motor Transducer InstallationHand-tighten only GPS Receiver InstallationIf you have… Then use Follow these steps to stem mount the GPS receiverAccess Under Mounting Location Access Under Mounting LocationTo the cable as shown No Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver OperationInstall the temperature probe accessory Routing the cable to the control headTesting the System Installation To test the installationPowering UP the Control Head Series 947c 3D Combo Title ScreenWHAT’S on the 3D Sonar Display TriplogWHAT’S on the 2D Sonar Display Bait Ball RTS Real Time Sonar WindowReal Time Sonar RTS Window Bottom PresentationView KEY POWER/LIGHT KEYKEY Functions Menu KEYExit KEY View Preset KeysWAY Cursor Control KEY Info KEYViews MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBeam Sonar View Beam Sonar ViewBIRD’S EYE View Bird’s Eye ViewChart/Bird’s Eye Combo View with Active Cursor CHART/BIRD’S EYE Combo ViewChart View Chart View with Active CursorCHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid Chart View with Grid SAVE, Edit or Delete a RouteEDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Normal Mode Sonar Tab, Advanced ModeNormal Operation Exit Normal operation by powering your 900 Series offSTART-UP Options Menu Start-Up Options MenuSimulator Self Test Accessory Test GPS Diagnostic ViewExit the Simulator by powering your 900 Series off System StatusAccessory Test Screen Accessory TestGPS Diagnostic View GPS Diagnostic ViewActive Side To Adjust Split Screen Position2D Sonar X-PRESS Menu Split PositionSensitivity To adjust the SensitivityTo adjust the Upper Range Upper RangeLower Range Chart SpeedBottom Lock 2D/3D Priority To adjust the Bottom RangeBottom Range To change the 2D/3D PriorityHighlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range To Reset 3D View Reset 3D ViewTo adjust the 3D History 3D HistoryHighlight Split Position on the Navigation X-Press Menu Navigation X-Press MenuSave Current Route Save Current TrackClear Current Track Skip Next WaypointRemove Target Cancel NavigationRemove Grid 3D Bottom Style Sonar Menu TAB2D Sonar Colors 3D Frame StyleTo change Beam Select 2D Beam SelectFish ID+ To set Fish ID+To change the Fish ID 3D Reference setting To change the Fish ID Sensitivity settingTo change the RTS Window setting Fish ID SensitivityKHZ Sensitivity Bottom ViewZoom Width Depth LinesSurface Clutter To change the Noise Filter settingTo change the Max Depth setting Noise FilterWater Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints Routes To change the Chart Orientation settingTo change the North Reference setting North ReferenceTrack MIN Distance Trolling Grid RotationTrackpoint Interval MAP DatumDelete ALL NAV Data Chart Menu TABExport ALL NAV Data To Export All Navigation DataLAT/LON Grid Chart Detail LevelMAP Borders Spot SoundingsSET MAP Offset Shaded DepthClear MAP Offset Fish ID Alarm Alarms Menu TABDepth Alarm To change the Depth Alarm settingTemp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone To change the Units Temp setting Setup Menu TABTo change the Units Depth setting Units DepthUnits Speed User ModeUnits Distance LanguageRestore Defaults Triplog ResetSelect Readouts Default Sonar View Customized Sonar View To Select ReadoutsLocal Time Zone Depth OffsetTemp Offset Daylight Saving TimeDate Format Position FormatTime Format Nmea OutputTo turn Nmea Output on or off SonarViews Menu TAB To turn Sonar on or offTroubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Display Problems Control head loses power at high speedsNoise re-appears Finding the Cause of NoiseOther electronic devices Boat’s engineYear Limited Warranty Humminbird Service PolicySeries Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Specifications Operating FrequencyAppendix a Contact Humminbird