Humminbird 77c manual Start-Up Options Menu, Normal Operation, Normal Simulator System Status

Page 13

M77_Man_Eng_531350-1_B.qxd 1/3/2005 4:29 PM Page 24

Start-Up Options Menu

Press the MENU key when the Title screen is displayed to access the Start-Up Options menu.

Use the UP or DOWN 4-WAY Cursor keys to position the cursor, then the RIGHT Cursor key to select one of the following choices. If you wait too long, the system will default to whichever menu mode happens to be highlighted:

•Normal

•Simulator

•System Status

•PC Connect (use with PC Connect Cable).

See the following paragraphs for more information about each of these choices.

Start-Up Options Menu

Normal Operation

Use Normal operation for on the water operation with a transducer connected. In addition, your Matrix™ Fishing System uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your Fishing System can be used on the water.

Exit Normal operation by powering your Fishing System off.

Simulator

Use the Simulator to learn how to use your Matrix™ Fishing System before taking your boat on the water. The Simulator is a very powerful tool that simulates on the water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation.

NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the Start-Up Options menu as opposed to letting the Fishing System enter Simulator automatically (as it will if a transducer is not connected and you do nothing during power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre- configure your Matrix™ Fishing System for on the water operation. Any menu changes you make will be saved for later use.

A message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your Fishing

System off.

Simulator

19

20

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Matrix 77c Operations Manual Thank You Table of ContentsSetup Menu Tab Alarms Menu TabViews Menu Tab Accessories Menu Tab Troubleshooting Sonar X-Press MenuDualBeam Plus Sonar How Sonar WorksWhat’s On the Display Temperature water surface temperatureSonar View ViewsReal Time Sonar RTS Window Understanding Sonar HistorySonar Zoom View Big Digits View 200/83 kHz Split Sonar View200/83 kHz Split Sonar View Big Digits ViewBottom Presentation Key Functions POWER/LIGHT KeyView Key Menu KeyPowering Up the Unit Accessory BusAdvanced features such as WeatherSense, GPS Exit KeyPress the Menu key once to display Menu SystemKeys to reactivate the X-Press Menu Change to the screenStart-Up Options Menu Exit Normal operation by powering your Fishing System offNormal Operation SimulatorPC Connect System StatusSonar X-Press Menu To adjust the Upper Range To adjust the SensitivitySensitivity Upper RangeLower Range Chart SpeedBottom View Zoom Level To adjust the Zoom LevelSonar Menu Tab Sonar Zoom View OnlyFish ID+ Beam SelectTo use Beam Select Highlight Beam Select on the Sonar main menuKHz Sensitivity Fish SensitivityDepth Lines Noise Filter Surface ClutterMax Depth To change the Water Type setting Alarms Menu TabSetting. Fresh, Salt, Default = Fresh Water TypeFish ID Alarm Depth AlarmLow Battery Alarm Temp AlarmUnits Depth Setup Menu TabUnits Temp Units DistanceTriplog Reset User ModeRestore Defaults Units SpeedSelect Readouts TemperatureVoltage To Select ReadoutsTemp Offset Depth OffsetSpeed Calibration Nmea OutputViews Menu Tab Accessories Menu TabTo Change the View Status of Any View Display Problems TroubleshootingProblem Possible Cause Control head loses power at high speedsFinding the Cause of Noise Matrix Fishing System AccessoriesIsolation Specifications Contact Humminbird
Top Page Image Contents