Pressure transmitter for gage pressure, Front view

SITRANS P measuring instruments for pressure

Transmitters for gage, absolute and differential pressure, flow and level

DS III, DS III PA and DS III FF series

Technical description

	Pressure transmitter for gage pressure
	Pressure transmitter for gage pressure		■Design
	• Measured variable: Gage pressure of aggressive and non-ag-		■Design

		gressive gases, vapors and liquids.
	•	Span (infinitely adjustable)
2		for DS III HART: 0.01 ... 400 bar g (0.145 ... 5802 psi g)
	• Nominal measuring range
		for DS III PA and FF: 1 ... 400 bar g (14.5 ... 5802 psi g)

Pressure transmitters for absolute pressure

•Measured variable: Absolute pressure of aggressive and non- aggressive gases, vapors and liquids.

•Span (infinitely adjustable)

for DS III HART: 8.3 mbar a ... 100 bar a (0.12 ... 1450 psi a)

•Nominal measuring range

for DS III PA and FF: 250 mbar a ... 100 bar a (3.63 ... 1450 psi a)

•There are two series:

-Gage pressure series

-Differential pressure series

Pressure transmitters for differential pressure and flow

•Measured variables:

-Differential pressure

-Small positive or negative pressure

-Flow q ~ √Δp (together with a primary differential pressure device (see Chapter "Flow Meters"))

•Span (infinitely adjustable)

for DS III HART: 1 mbar ... 30 bar (0.0145 ... 435 psi)

•Nominal measuring range

for DS III PA and FF: 20 mbar ... 30 bar (0.29 ... 435 psi)

Pressure transmitters for level

•Measured variable: Level of aggressive and non-aggressive liquids in open and closed vessels.

•Span (infinitely adjustable)

for DS III HART: 25 mbar ... 5 bar (0.363 ... 72.5 psi)

•Nominal measuring range

for DS III PA and FF: 250 mbar ... 5 bar (3.63 ... 72.5 psi)

•Nominal diameter of the mounting flange

-DN 80 or DN 100

-3 inch or 4 inch

In the case of level measurements in open containers, the low- pressure connection of the measuring cell remains open (mea- surement "compared to atmospheric").

In the case of measurements in closed containers, the lower- pressure connection has to be connected to the container in or- der to compensate the static pressure.

The wetted parts are made from a variety of materials, depend- ing on the degree of corrosion resistance required.

Front view

The transmitter consists of various components depending on the order. The possible versions are listed in the ordering infor- mation. The components described below are the same for all transmitters.

The rating plate (3, Figure "Front view") with the Order No. is lo- cated on the side of the housing. The specified number together with the ordering information provide details on the optional de- sign details and on the possible measuring range (physical properties of built-in sensor element).

The approval label is located on the opposite side.

The housing is made of die-cast aluminium or stainless steel pre- cision casting. A round cover is screwed on at the front and rear of the housing. The front cover (6) can be fitted with a viewing pane so that the measured values can be read directly on the digital display. The inlet (4) for the electrical connection is lo- cated either on the left or right side. The unused opening on the opposite side is sealed by a blanking plug. The protective earth connection is located on the rear of the housing.

The electrical connections for the power supply and screen are accessible by unscrewing the rear cover. The bottom part of the housing contains the measuring cell with process connection

(1). The measuring cell is prevented from rotating by a locking screw (8). As the result of this modular design, the measuring cell and the electronics can be replaced separately from each other. The set parameter data are retained.

At the top of the housing is a plastic cover (5), which hides the input keys.

2/64

Siemens FI 01 · 2009