MENU FIELD DEFINITIONS
PICTURE
Brightness: Adjusts the white level of the video screen image (0 to 100).
Contrast: Adjusts the black level of the video screen image (0 to 100).
Sharpness: Adjusts the picture softer or sharper (0 to 15).
Color: Adjusts the color saturation of the video signal (0 to 100).
Tint: Adjusts the range of color: green to red (0 to 100). This function is only available in NTSC mode; it is not available in PAL/SECAM.
Color Temp: Selects the temperature: Normal, Cool, or USER.
If you select USER, then choose from the following calibrations:
•Red: Adjusts gain for red (0 to 100).
•Green: Adjusts gain for green (0 to 100).
•Blue: Adjusts gain for blue (0 to 100).
SCREEN
Scan Mode: Select UNDER, FULL, OVER, or 4:3. The default setting is FULL. (The 4:3 mode only applies to the
PIP Mode: Select PIP OFF, PIP ON, or PBP ON.
PIP Input: Select VIDEO 1, VIDEO 2, CAMERA, or MEDIA. (Audio will not play when a file is displayed in the PIP window. To play audio, the file must be displayed in the main window.)
PIP Swap: Select SWAP to change from MAIN to PIP.
PIP Size: Select the PIP size: SMALL, NORMAL, or LARGE.
PIP Location: Select the PIP location: R/B (right bottom), L/B (left bottom), L/T (top left), or R/T (top right).
PIP Scan Mode: Select the PIP size for the screen: UNDER, FULL, OVER, or 4:3. The default setting is FULL. (The 4:3 mode only applies to the
SETUP
Input: Select VIDEO 1, VIDEO 2, CAMERA, or MEDIA.
Language: Select ENGLISH, ITALIAN, FRENCH, SPANISH, or GERMAN, for the OSD display.
Sound Mute: Select ON (silences the sound) or OFF (returns the sound).
Key Lock: Prevents unauthorized operation of the equipment by locking the buttons. Authorized users can release the key lock feature by pressing and holding the SOURCE button for five seconds.
IQE: Select ON or OFF for the image quality enhancement (IQE) function; this feature is only available on the
Noise Reduction: Select OFF, WEAK, or STRONG to control the video signal’s background noise.
OSD Mode Label: Select ON or OFF. ON displays the Mode (input source) OSD.
PVM Setup
Auto Power ON: Select the video input to be activated when power is restored after an electricity failure. Select OFF, VIDEO 1, VIDEO 2, CAMERA, or MEDIA.
Light Sensor Mode: Automatically turns on or off the monitor based on the light intensity.
L. Sensor Sensitivity: Sets the light intensity at which the monitor is turned off and on (1 to 100). The 100 setting is the more sensitive.
Light Sensor Delay: Sets the time that the Auto Day/Night feature pauses before being activated (5 to 30 seconds).
Video Loss Sleep: This is an ON/OFF function. ON sets the function that puts the monitor in sleep mode after video has been lost for
30 seconds. When a signal is detected, the monitor turns on again. To restore power immediately, use the power button on the remote control or the power button on the side of the PVM cabinet.
PIR Mode: Sets the motion detection mode : OFF, FULL, PIP, or PIP. This determines the length of time a selected video source triggered by motion detection displays on the screen (5 to 20 seconds).
PIR Sensitivity: Sets the motion detection sensitivity: LOW, MIDDLE, and HIGH. The typical detection for LOW is 16.4 to 23.0 feet (5 to 7 m); for MIDDLE, 26.2 to 32.8 feet (8 to 10 m); and for HIGH, 32.8 to 45.9 feet (10 to 14 m).
16 | C2943M (1/08) |