Precautions, Installation | White Rodgers 36C specification

PRECAUTIONS

DO NOT BEGIN INSTALLATION UNTIL YOU READ THE FOLLOWING PRECAUTIONS.

!WARNING

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

1.Failure to turn off electric or main gas supply to heating system could cause personal injury and/or property damage by shock, gas suffocation, fire, and/or explosion.

2.Do not use this control on circuits exceeding specified voltage. Higher voltage will damage the control and may cause shock or fire hazard.

3.NEVER USE FLAME OR ANY KIND OF SPARK TO CHECK FOR GAS LEAKS–COULD CAUSE FIRE AND/OR EXPLOSION.

4.Do not use a control set for natural gas with LP gas, or a control set for LP gas with natural gas. Personal injury and/or property damage, gas suffocation, fire, and/or explosion may result.

!CAUTION

1.Do not short out terminals on gas valve or primary control to test. Short or incorrect wiring can cause equipment damage, property damage and/or personal injury.

2.This control is not intended for use in locations where it may come in direct contact with water. Suitable protection must be provided to shield the control from exposure to water (dripping, spraying, rain, etc.).

INSTALLATION

NOTE

All piping must comply with local codes, ordinances, and/or national fuel gas codes.

1.Turn off electrical power to the system at the fuse box or circuit breaker. Also turn off the main gas supply.

2.If replacing an existing valve, disconnect all plumbing and electrical connections from the old control.

3.The control may be installed in any position except upside down (see figure 1). The arrow on the bottom plate indicates the direction of gas flow through the valve.

4.You should use new pipe that is properly chamfered, reamed, and free of burrs and chips. If you are using old pipe, be sure it is clean and free of rust, scale, burrs, chips, and old pipe joint compound.

5.Apply pipe joint compound (pipe dope) or teflon tape that is approved for all gases, only to the male threads of the pipe joints. DO NOT apply compound or teflon tape to the first two threads (see figure 2 for typical piping connections).

6.If you are using a vise or open-end wrench to hold the valve while installing piping, do not tighten excessively, as this may damage the valve.

7.See wiring pages 3-6 when making electrical con- nections. After all gas and electrical connections are completed, turn gas on and check for gas leaks with leak detection solution or soap suds. Bubbles forming indicate a leak. SHUT OFF GAS AND FIX ALL LEAKS IMMEDIATELY.

Upright, 90° from upright or vertical

	INLET BOSS
UPRIGHT	UP OR DOWN
	LEFT OR RIGHT

NOTE: Control shown may not be identical to replacement control.

Figure 1. Mounting positions

Drop

Horizontal

Gas Valve

NOTE:

Riser

3 in.

Always Include

A Drip Leg In Piping

minimum

Drop

Tubing Gas

Supply

Gas Valve

Riser

Horizontal

Gas Valve

3 in.

minimum

Piped Gas

Supply

Figure 2. Typical gas valve piping

36C specifications

The White Rodgers 36C is a versatile and reliable thermostat designed to enhance temperature control within residential and commercial environments. Part of the White Rodgers brand, known for its innovation in heating, ventilation, and air conditioning (HVAC) technologies, the 36C model stands out due to its user-friendly features and advanced functionalities.

One of the primary features of the White Rodgers 36C thermostat is its digital display, which provides clear and concise readings of indoor temperatures. This LCD display is easy to read, allowing users to adjust settings without hassle, even in low-light conditions. The thermostat is equipped with a user-friendly interface that simplifies programming, enabling users to set schedules according to their specific heating and cooling needs.

The 36C model utilizes microprocessor technology, which enhances its accuracy and reliability in temperature regulation. This technology ensures that the thermostat maintains the desired temperature levels with minimal fluctuations, contributing to overall energy efficiency. By intelligently controlling HVAC systems, the 36C helps reduce energy consumption, leading to lower utility bills and a smaller carbon footprint.

Another key characteristic of the White Rodgers 36C is its compatibility with various heating and cooling systems, including gas, oil, and electric units. This adaptability allows homeowners and businesses to integrate the thermostat seamlessly into their existing HVAC setup. Additionally, the thermostat supports multi-stage heating and cooling applications, making it a suitable choice for those with more complex temperature control needs.

For enhanced comfort and convenience, the White Rodgers 36C comes with programmable features. Users can easily program specific time frames for heating and cooling, ensuring that the environment is comfortable upon arrival while maximizing energy savings during periods of inactivity. This programmable functionality is particularly beneficial for families and individuals with busy schedules.

Furthermore, the White Rodgers 36C promotes ease of installation and maintenance. Its compact design and straightforward setup process allow users to replace older models without the need for professional assistance. The thermostat's durability and long-lasting performance underline its reliability as an essential component of any HVAC system.

In summary, the White Rodgers 36C thermostat combines advanced technology, user-friendly features, and compatibility with various heating and cooling systems. Its digital interface and programmable capabilities provide enhanced control and convenience, making it a popular choice for maintaining optimal indoor climate conditions. With a focus on energy efficiency and comfort, the White Rodgers 36C stands out as a reliable solution for effective HVAC management.