Cobra Electronics MR HH330 owner manual Memory Location Mode, To Program Memory Locations

Page 18

Operating Your Radio

MEM/ESC Button

Memory Location Number

Channel Up/Down Buttons

Channel Number

Advanced Operation

Memory Location Mode

Your radio has unlimited memory locations for storing your most frequently used channels. These memory locations can be selected individually or can be scanned. (See page 33 under Memory Location Scan.)

To enter Memory mode, press MEM/ESC button. The display will show the MEM icon and the Memory Channel bank will be activated and displayed.

To Program Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the memory location (00-99) you want to program.

3.Press the MEM/ESC button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel you want to store into the selected memory location.

5.Press the MEM/ESC button to program that channel. The memory location number will flash again.

Repeat steps 2 through 5 to program as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to Memory mode.

7.Press and release the MEM/ESC button again to return to Marine Standby mode.

Operating Your Radio

MEM Icon

Advanced Operation

To Recall a Stored Memory Location:

1.Press the MEM/ESC button. The MEM icon will be turned On.

2.Press the Channel Up/Down button to select the memory location. If a memory location has been programmed, its associated channel will display on the LCD. Your radio is now in Marine Standby mode on the selected memory location.

To Exit Memory Location Mode:

Press the MEM/ESC button to return the radio to Marine Standby mode. The last channel used in Marine Standby mode will now be displayed on the LCD and the MEM icon will disappear.

To Erase Stored Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the memory location you want to erase.

3.Press the MEM/ESC button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel to read “00” at the selected memory location.

5.Press the MEM/ESC button to erase that channel.

Repeat steps 2 through 5 to erase as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to Memory mode.

7.Press and release the MEM/ESC button again to return to Marine Standby mode.

30 English

Nothing Comes Close to a Cobra® 31

Page 17 Page 19
Image 18
Page 17 Page 19
Contents For Assistance in the U.S.A Radio Controls IndicatorsOur Thanks to You Customer Assistance For Assistance Outside the U.S.AAlkaline batteries. Good for emergency Backlit LCD Screen Product FeaturesBacklit LCD Liquid Crystal Display Screen Near or distant callingTable of Contents Safety Training Information Important Safety InformationGeneral Precautions Important Safety InformationRecommendations for Marine Communication Recommendations for Marine CommunicationFCC Licensing Information Belt Clip Included in this PackageWrist Strap and Belt Clip Wrist StrapInitial Charge Installing the Battery PackBatteries and Charger Batteries and ChargerTo Remove Battery Pack from Radio Maintaining the Battery ChargeAlkaline Batteries Getting Started Getting StartedCommon Radio Functions Radio Speaker and MicrophoneBacklight/Key Lock Button Channel Up/Down ButtonsScan Button High/Medium/Low H-M-L Power Button Setup Mode ProgrammingSetup Mode Programming To Toggle Between H-M-L Power ModesSquelch Control USA/International/Canada Channel MapsCall Tone Alert Standby/Receive Transmit Roger Beep ModeKey Tone Mode Call Tone SelectNoaa Test Alert System Marine Standby and Receive Rx ModeNoaa Emergency Weather Alert Standby/Receive and TransmitAdvanced Operation Weather WX Standby ModeChannel 16/9 Mode Advanced OperationTri-Watch Mode Tri-Watch Setup To Program or Edit the Tri-Watch ChannelsUsing Tri-Watch Tri-Watch Scan Mode To Program Memory Locations Memory Location ModeTo Exit Memory Location Mode To Recall a Stored Memory LocationTo Enter Channel Scan Channel Scan ModeMemory Location Scan Mode To Enter Memory Location ScanBurp Feature Floating FeatureMaintenance Troubleshooting Floating RadioVHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair is calling the vessel Vagabond Radiotelephone Calls Emergency Messages Distress ProcedureEmergency Messages and Distress Procedure Radiotelephone CallsMarine Emergency Signals Marine Distress ProcedureIf You Hear a Distress Call Exclusions This limited warranty does not apply Warranty and Trademark AcknowledgementLimited 3-Year Warranty For Products Purchased In The U.S.AProduct Service Product ServiceSpecifications SpecificationsVHF Marine Channel Assignments Navigational Public Correspondence Marine OperatorPort Operations Maritime Control04A 01A03A 05A20A 18A19A 21A61A 25B28B 62A66A Communications in lower Mississippi River80A 78A79A 81AWeather Channel Assignments Weather Channel AssignmentsAsignaciones de canales meteorológicos Alkaline Battery Tray AccessoriesAccessories Long Life Battery
Top Page Image Contents