Cobra Electronics MR HH400 EU owner manual Memory Locations

Page 21

400-BR-F 6/23/04 2:12 PM Page 38

Operating Your Radio

Tri-Watch Button

Advanced Operation

To enter Tri-Watch mode:

1.From Standby mode, press the Tri-Watchbutton.

The Tri-Watchicon will appear on the LCD and the radio will scan among Channel 16, tri-watch location

Tri-Watch Mode

Talk or Channel Up/Down

ab

one and tri-watch location two. A signal on any one

of the three locations will stop the scan for ten seconds to allow you to listen to the traffic on that location.

To exit Tri-Watch mode:

1.Press the Tri-Watchbutton.

The icon will disappear from the LCD and the radio will return to Standby mode status.

During Tri-Watch (while receiving an incoming transmission), you can choose from the following:

a. Press the Talk button to remain on that tri-watch location and return to Standby mode.

b. Press the Channel Up or Channel Down button to resume scanning tri-watch locations.

If you do not press any buttons within ten seconds, your radio will automatically resume scanning tri-watch locations.

During Tri-Watch (while not receiving a transmission), you can choose from the following:

a. Press the Talk button to communicate on the last tri-watch location scanned and return to Standby mode.

b. Press the Channel Up or Channel Down button to change scan direction.

Advanced Operation

Operating Your Radio

Memory Locations

Your radio has ten Memory Locations for storing your most frequently used channels. These Memory Locations can be selected individually or can be scanned. (See page 41 under memory location scan.)

Memory Button

Memory Location Number

Channel Up/Down Buttons

Channel Number

Memory Icon

To program memory locations:

1.Press and hold the Memory button. The memory location number will start flashing and the Memory icon will be turned On.

2.Use the Channel Up or Channel Down button to change to the memory location (0 to 9) you want to program.

3.Press the Memory button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up or Channel Down buttons to change to the channel you want to store in the selected memory location.

5.Press the Memory button to program that channel. The memory location number will flash again.

Repeat steps 2 to 5 to program as many additional memory locations as you want, up to a total of ten.

6.Press and hold the Memory button. This will return the radio to Memory mode.

7.Press and release the Memory button again to return to Standby mode.

To recall a stored memory location:

1.Press the Memory button. The Memory icon will be turned On.

2.Press the Channel Up or Channel Down button to select the memory location (0 to 9). If a memory location has been programmed, its associated channel will be shown on the LCD.

Your radio is now in Standby mode on the selected memory location.

To exit Memory Location mode:

1.Press the Memory button to return the radio to Standby mode on the last channel shown on the LCD before entering Memory Location mode.

 

 

 

 

38 English

Nothing comes close to a Cobra® 39

Image 21
Contents Our Thanks to You Customer Assistance For Warranty, Product Service Accessory InformationCustomer Assistance ΑPTTable of Contents Radio Controls and IndicatorsImportant Safety Information General PrecautionsImportant Safety Information Recommendations for Marine Communication Recommendations for Marine CommunicationLicensing Information VHF Marine Radio Procedures Radiotelephone Calls Voice CallingVoice Calling Radiotelephone CallsEmergency Messages and Distress Procedure Emergency Messages Distress ProcedureMarine Emergency Signals Three spoken international emergency signals areTell where you are Marine Distress ProcedurePress Talk button and say SayVHF Marine Channel Assignments Channel Frequency Power NumberCanada USA Channel UseReceive Limits Frequency Power Number Int’l21A U.S. government only Canada coastguard only 23A Government OnlyDigital Selective Calling voice communications not allowed 64A U.S. government only Canada Commercial FishingCanada U.S.A You should find all of the following items Included in this Package Antenna, Wrist Strap and Belt ClipWrist Strap Included in this PackageAntenna, Wrist Strap Belt Clip Installing the BatteriesBatteries and Charger Belt ClipInitial Charge Maintaining the Battery ChargeVolume Power On-OffGetting Started SquelchInternational/Canada/U.S.A. Channel Maps Transmit Power OutputChannels BacklightKey Lock Standby/Receive and TransmitTransmit Standby and ReceiveChannel Advanced OperationTri-Watch Advanced OperationMemory Locations Memory Location Scan Channel ScanTo enter channel scan From Standby mode, press the Scan buttonMaintenance Maintenance TroubleshootingTroubleshooting Problem Possible Causes SolutionsSpecifications SpecificationsDeclaration of Conformity
Related manuals
Manual 24 pages 40.94 Kb