Ingersoll-Rand 8 and 10 BORES, 6, 5, 1/1/2002 Provenair Seal Kits, Rkn X X X X B, Heads and Caps

PROVENAIR SEAL KITS

RKN X X X X B

CYLINDER TYPE

A- Double Acting, Single Rod End

B- Double Acting, Double Rod End

BORE SIZE
Q	- 1-1/2”	5	- 5”
S	- 2”	6	- 6”
T	- 2-1/2”	8	- 8”
W - 3-1/4”		Y	- 10”
4	- 4”	NOTE: All seal kits include wear strip and cushion seals.

CUSHIONED BOTH ENDS SEALS

B - Nitrile; Nitrile, Mag

S- Self-Lube; Self-Lube, Mag V - Viton; Viton, Mag

ROD DIAMETER

K	- 5/8”	Q	- 1-3/4”
M	- 1”	S	- 2”
P	- 1-3/8”

HEADS AND CAPS

CYLINDER	1-1/2” BORE		2” BORE		2-1/2” BORE		3-1/4” BORE		4” BORE
TYPE	HEAD	CAP	HEAD	CAP	HEAD	CAP	HEAD	CAP	HEAD	CAP
NON-CUSHIONED	119462	119471	119480	119489	119498	119507	119516	119525	119534	119543
CUSHIONED	119651	119666	119654	119669	119657	119672	119660	119675	119663	119678
NON-CUSHIONED MS4	119464	119473	119482	119491	119500	119509	119518	119527	119536	119545
CUSHIONED MS4	119652	119667	119655	119670	119658	119673	119661	119676	119664	119679
NON-CUSHIONED TRUNNION	119901	119902	119903	119904	119905	119906	119907	119908	119909	119910
CUSHIONED TRUNNION	119653	119668	119656	119671	119659	119674	119662	119677	119665	119680
	119752	119754	119756	119758	119760	119762	119764	119766	119768	119770
CUSHIONED FEM. RET. BOLT	114063	114064	114065	114066	114067	114068	114069	114070	114071	114072
	119835	119836	119839	119840	119843	119844	119847	119848	119851	119852
	119877	119878	119879	119880	119881	119882	119883	119884	119885	119886

119577-( ) SPACER INSTALLATION

To replace tie rod cylinders that have end caps made from castings (such as Wabco, Taiyo and Aro series 38 / 39), use
spacers as called out below.		MF1 Head Flange
	Q Spacer
		Mounting Screw for MF1 mount (4 req’d) g
	Cylinder Head

“B”

“B”

“A”

gNot Supplied

BORE	SPACER	“A”	“B”	CAP SCREW g	TORQUE
SIZE					(FT LBS)
1-1/2”	119577-150	.375”	2.000”	1/4” - 28 x 2-1/4”	9
2”	119577-200	.375”	2.500”	5/16” - 24 x 2-1/4” (Low Head)	16
2-1/2”	119577-250	.375”	3.000”	5/16” - 24 x 2-1/4” (Low Head)	21
3-1/4”	119577-325	.625”	3.750”	3/8” - 24 x 2-3/4”	35
4”	119577-400	.625”	4.500”	3/8” - 24 x 2-3/4”	49

QWhen used with MF1 flange, spacer 119577-( ) is mounted between head and flange and requires 4 mounting screws of the size listed in the table.

QWhen used without MF1 flange, spacer 119577-( ) is slid over piston rod and bushing, against cylinder head. No new mount- ing screws are required. Spacer is attached using Loctite or “superglue”.