Raymarine L265 manual Mounting the Transom-Mount Transducer

Page 14

If the propeller can be turned to steer the boat, allow at least 2" (50 mm) beyond the swing radius of the propeller. This will prevent the propeller from damaging the transducer when it is turned. After installation, check the clearance by turning the wheel so the propeller swings toward the transducer. There should always be a 2” (50 mm) clearance.

If your boat has twin propellers (outboard or inboard-outboard), place the transducer near the centerline of the boat.

Do not mount the transducer behind any hull fittings, intakes, or other parts which extend from the hull. These may cause turbulence or air bubbles.

The bracket has a quick-release mechanism. This may reduce damage by allowing the transducer to flip up if it hits any debris or the bottom. See Fig. 2-4. Allow enough clearance above the transducer so that it can swing upward completely. This is about 10" (254 mm) measured from the bottom of the transom.

If considering the Sidelooker option, look for a mounting location where the Sidelooker array will not be blocked by the engine housing or other mounted hardware.

If the boat will be carried on a trailer, be sure the transducer will not hit any rollers, bunks or fittings on the trailer.

Mounting the Transom-Mount Transducer

1.On a boat with a fiberglass hull, the leading edge of the transducer should extend 1/8" (3.2 mm) to 1/4" (6 mm) below the bottom edge of the hull. See Fig. 2-5. On an aluminum hull, the transducer should extend a bit more – 1/4" (6 mm) to 3/8" (9 mm). If the boat will be operated at high speeds, the transducer may be mounted closer to the centerline of the hull.

2.The lower surface of the transducer should tilt down toward the rear at a slight angle (2° to 5°). The mounting bracket includes a wedge. Depending on the angle of the transom on your boat, you may need this wedge to get the correct angle for the bottom of the transducer.

3.Looking at the rear of the boat, be sure the bracket is vertical (perpen- dicular to the water line).

4.Hold the bracket (and the wedge, if used) against the transom and trace the positions of the screw slots.

Installation

9

Image 14
Contents Distributed by FishFinder L265 Contents Cleaning Instructions Simulator Deep AlarmFish Alarm How to Contact RaymarineList of Figures Introduction About the FishFinder L265Standard Equipment Optional AccessoriesSystem Components Standard TransducersIntroduction Selecting the Correct Type of Transducer InstallationAbout the Transducer Use a transom-mount transducer if Use a thru-hull transducer ifUse an in-hull transducer if Assembling the Transducer BracketUse a low-profile transducer if Use a trolling motor transducer ifPositioning the Transom-Mount Transducer No!No!No Mounting the Transom-Mount Transducer Mounting the Optional Sidelooker Transducer Installing Sidelooker Transducer Installation Installation Notes In-Hull Transducer Mounting the Display Unit Standard Mount Dismounting the Display Unit Mounting the Display Unit Flush MountInstallation Flush-mount Installation Installing the Transducer Cable Installing Cable on Transom Installing the Transducer Cable Sidelooker Option DC Power Connections Installation Operating Instructions Controls on Display UnitControl pad Turning the Power On and OffSetup Memory Lamp/Contrast Menu Press Lamp/Contrast Menu appears when you first pressMode. If you do not make any changes to the settings Within 7 seconds, the unit automatically exits fromReturn to FishFinder Operating Pages FishFinder Range, auto sensitivity, and auto zoom features Auto features onIf any of the automatic features are turned on, the Auto Top of displayAuto zoom on Z Center of displayFor more on this, see Choosing the Frequency If the fish is detected using the narrow 200 kHz beam,When the fish symbol function is off Bottom of displayChoosing a Frequency Fish Indications Operating Instructions Bottom Indications Performance Modes Zoom PressOperating Instructions Scope Bottom Coverage Operating Instructions Digital Sidelooker Operating Instructions Distance from the boat to the fish. Remember that this Distance is measured sideways. See FigOperating Instructions Setup Instructions Setup MenuBottom in the display Range SettingOr falls, the FishFinder will adjust the range to keep Sensitivity Setting Chart Speed Setting Manual sensitivityZoom Setting Same information is displayed in a smaller horizontal spaceParticularly useful when fishing for species of fish which Bottom contour, and adjusts the position of the ZoomWindow accordingly with changes in depth. This feature is Arrow on the Page control pad to select Auto orYour choice Frequency SettingFrequency System Setup Display By showing an arch-shaped line. See -5. This kind General, the larger the symbol, the larger the fish. ForMore information, see the section on Fish Indications Display does not include the depth readings for the fishThis feature helps to show the difference between Echoes are displayed in black. When the feature isUsing a solid area of black or gray Boat. See -10. If you have installed thisWay, the unit will trigger an alarm if the anchor drags Into deep water and trigger the alarm, the letter D willDeep Alarm features when you are anchored. Set the limits Silence the buzzer for the current alarm condition.Setup Instructions for Sidelooker Button to go back to the Sidelooker If you press Resetting the Unit to Factory DefaultsDefault Settings Troubleshooting Suggestions Maintenance and TroubleshootingCleaning Instructions Maintenance and Troubleshooting Display unit does not see the bottom or fish Display unit shows lots of background noise For accessories and parts How to Contact RaymarineFor marine product and services information For product repair serviceRaymarine in Europe Prepaid Return Service Maintenance and Troubleshooting Specifications General InformationFishFinder Functions Connector Diagrams Glossary of Terms GlossaryNautical mile 6076 feet Limited Warranty Certificate Warranty LimitationsFactory Service Centers

L265 specifications

The Raymarine L265 is a cutting-edge piece of marine technology designed specifically for navigation and communication on the water. This integrated system combines advanced features and technologies, ensuring that boaters have the best tools available for safety and efficiency.

One of the standout characteristics of the Raymarine L265 is its high-resolution display. The system typically incorporates a bright, sunlight-readable screen that provides exceptional visibility in all lighting conditions. The intuitive interface allows users to easily access various functions, making navigation more comfortable and streamlined.

At the heart of the L265's functionality is its award-winning Raymarine navigation software. This software offers a range of features including advanced chart plotting, waypoint management, and the ability to overlay additional information such as weather data and radar images. Users can benefit from detailed charts and maps, ensuring they can navigate through even the most challenging waters with confidence.

The L265 also boasts built-in GPS capabilities that provide accurate positioning information. The multi-channel GPS receiver ensures rapid satellite acquisition and consistent performance, even in areas with limited visibility. This reliability is crucial for safe navigation at sea.

In addition to its navigational prowess, the L265 incorporates sophisticated communication technologies. This system is compatible with various marine communication protocols, allowing boaters to connect with other devices on board, such as VHF radios and AIS transponders. This feature enhances situational awareness, giving users the ability to monitor vessel traffic and communicate effectively with nearby boats.

Safety is paramount in any marine setting, and the Raymarine L265 reinforces this with its integrated alarm systems. Users will receive alerts for a variety of conditions, such as low battery levels and navigational hazards. This level of vigilance can be vital in ensuring safe travels.

Furthermore, the Raymarine L265 often features expandable options, allowing users to integrate additional sensors and devices tailored to their specific needs. This means as technology advances or user demands change, the L265 can adapt, providing longevity and versatility.

In summary, the Raymarine L265 is an exemplary navigation and communication system, merging high-resolution displays, advanced software, dependable GPS, and comprehensive communication capabilities. With a focus on safety, adaptability, and user-friendly design, it stands out as an essential tool for any serious boater looking to enhance their maritime adventures.