Raymarine L265 manual Installing the Transducer Cable

Page 23

6.Separate the display unit from the mounting bracket. (See Fig. 2-12.) Press the large button in the center of the bracket to separate the bracket arms. The display unit is attached to the arms by two screws. Each screw is covered by a cap. Locate the small slot beside each cap and pry upward using a small screwdriver. Remove the caps, then the two screws and the two wave washers. Save these parts in case you ever want to use the mounting bracket.

7.Screw the threaded studs into the holes on the rear of the display unit.

8.Set the display unit into place to be sure that it will fit correctly. Thread the wing-nuts onto the threaded studs to hold the display unit in place temporarily.

9.Install the DC power wiring as described later in this section. Finally, finish the installation. Hold the gasket in place around the opening. Fit the display unit into the cutout. From the rear, screw the thumb- screws securely onto the threaded studs to hold the unit in place.

Installing the Transducer Cable

A 20 foot length of cable, with the connector attached, is supplied with the transducer. During the installation, do not cut the transducer cable or remove the connector. Do not try to shorten or splice the cable. The transducer cable includes several wires, along with shielding and insulation. If the cable is cut, it cannot be repaired. (Cutting the cable will also void the warranty.) During installation, if you need to drill any holes for the cable, they must be large enough to accept the connector. This will allow you to make the installation without cutting the wire.

1.Route the cable up and over the top edge of the transom. See Fig. 2- 13. Secure the cable using cable clamps. (These clamps are available from your local marine equipment supplier.)

If you do not want to expose the cable on the deck, you may drill a new hole (3/4" or 19 mm) through the transom for the cable. (Re- member – this hole must be large enough to accept the cable with the connector attached. Do not cut the cable!) To seal the opening, use a feed-thru cap where the cable passes through the transom.

2.Run the cable through the interior of the boat. If the transducer cable runs near another electrical wire, it may pick up electrical interference or “noise.” To reduce this, try to keep the transducer cable separated

18

Installation

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Distributed by FishFinder L265 Contents How to Contact Raymarine Simulator Deep AlarmFish Alarm Cleaning InstructionsList of Figures About the FishFinder L265 IntroductionStandard Transducers Optional AccessoriesSystem Components Standard EquipmentIntroduction Selecting the Correct Type of Transducer InstallationAbout the Transducer Use a thru-hull transducer if Use a transom-mount transducer ifUse a trolling motor transducer if Assembling the Transducer BracketUse a low-profile transducer if Use an in-hull transducer ifPositioning the Transom-Mount Transducer No!No!No Mounting the Transom-Mount Transducer Mounting the Optional Sidelooker Transducer Installing Sidelooker Transducer Installation Installation Notes In-Hull Transducer Mounting the Display Unit Standard Mount Mounting the Display Unit Flush Mount Dismounting the Display UnitInstallation Flush-mount Installation Installing the Transducer Cable Installing Cable on Transom Installing the Transducer Cable Sidelooker Option DC Power Connections Installation Controls on Display Unit Operating InstructionsControl pad Turning the Power On and OffSetup Memory Within 7 seconds, the unit automatically exits from Press Lamp/Contrast Menu appears when you first pressMode. If you do not make any changes to the settings Lamp/Contrast MenuReturn to FishFinder Operating Pages FishFinder Top of display Auto features onIf any of the automatic features are turned on, the Auto Range, auto sensitivity, and auto zoom featuresCenter of display Auto zoom on ZBottom of display If the fish is detected using the narrow 200 kHz beam,When the fish symbol function is off For more on this, see Choosing the FrequencyChoosing a Frequency Fish Indications Operating Instructions Bottom Indications Performance Modes Press ZoomOperating Instructions Scope Bottom Coverage Operating Instructions Digital Sidelooker Operating Instructions Distance is measured sideways. See Fig Distance from the boat to the fish. Remember that thisOperating Instructions Setup Menu Setup InstructionsBottom in the display Range SettingOr falls, the FishFinder will adjust the range to keep Sensitivity Setting Manual sensitivity Chart Speed SettingSame information is displayed in a smaller horizontal space Zoom SettingArrow on the Page control pad to select Auto or Bottom contour, and adjusts the position of the ZoomWindow accordingly with changes in depth. This feature is Particularly useful when fishing for species of fish whichYour choice Frequency SettingFrequency System Setup Display Display does not include the depth readings for the fish General, the larger the symbol, the larger the fish. ForMore information, see the section on Fish Indications By showing an arch-shaped line. See -5. This kindBoat. See -10. If you have installed this Echoes are displayed in black. When the feature isUsing a solid area of black or gray This feature helps to show the difference betweenSilence the buzzer for the current alarm condition. Into deep water and trigger the alarm, the letter D willDeep Alarm features when you are anchored. Set the limits Way, the unit will trigger an alarm if the anchor dragsSetup Instructions for Sidelooker Button to go back to the Sidelooker If you press Resetting the Unit to Factory DefaultsDefault Settings Troubleshooting Suggestions Maintenance and TroubleshootingCleaning Instructions Maintenance and Troubleshooting Display unit does not see the bottom or fish Display unit shows lots of background noise For product repair service How to Contact RaymarineFor marine product and services information For accessories and partsRaymarine in Europe Prepaid Return Service Maintenance and Troubleshooting General Information SpecificationsFishFinder Functions Connector Diagrams Glossary Glossary of TermsNautical mile 6076 feet Warranty Limitations Limited Warranty CertificateFactory Service Centers

L265 specifications

The Raymarine L265 is a cutting-edge piece of marine technology designed specifically for navigation and communication on the water. This integrated system combines advanced features and technologies, ensuring that boaters have the best tools available for safety and efficiency.

One of the standout characteristics of the Raymarine L265 is its high-resolution display. The system typically incorporates a bright, sunlight-readable screen that provides exceptional visibility in all lighting conditions. The intuitive interface allows users to easily access various functions, making navigation more comfortable and streamlined.

At the heart of the L265's functionality is its award-winning Raymarine navigation software. This software offers a range of features including advanced chart plotting, waypoint management, and the ability to overlay additional information such as weather data and radar images. Users can benefit from detailed charts and maps, ensuring they can navigate through even the most challenging waters with confidence.

The L265 also boasts built-in GPS capabilities that provide accurate positioning information. The multi-channel GPS receiver ensures rapid satellite acquisition and consistent performance, even in areas with limited visibility. This reliability is crucial for safe navigation at sea.

In addition to its navigational prowess, the L265 incorporates sophisticated communication technologies. This system is compatible with various marine communication protocols, allowing boaters to connect with other devices on board, such as VHF radios and AIS transponders. This feature enhances situational awareness, giving users the ability to monitor vessel traffic and communicate effectively with nearby boats.

Safety is paramount in any marine setting, and the Raymarine L265 reinforces this with its integrated alarm systems. Users will receive alerts for a variety of conditions, such as low battery levels and navigational hazards. This level of vigilance can be vital in ensuring safe travels.

Furthermore, the Raymarine L265 often features expandable options, allowing users to integrate additional sensors and devices tailored to their specific needs. This means as technology advances or user demands change, the L265 can adapt, providing longevity and versatility.

In summary, the Raymarine L265 is an exemplary navigation and communication system, merging high-resolution displays, advanced software, dependable GPS, and comprehensive communication capabilities. With a focus on safety, adaptability, and user-friendly design, it stands out as an essential tool for any serious boater looking to enhance their maritime adventures.
Top Page Image Contents