Humminbird 987C SI COMBO manual SAVE, Edit or Delete a Route

Page 51

www98x Manual..reelsche531376-1 A.qxd m2/23/2005atic11:40..coAM mPage 51

SAVE, EDIT OR DELETE A ROUTE

(987c SI Combo models only)

Save the current route: While you are navigating, the current route can be saved. From the Navigation X-Press™ Menu, select Save Current Route and press the RIGHT Cursor key. Navigation will continue.

Display the Routes submenu: From any view, press the MENU key twice to display the Main Menu System, then use the RIGHT Cursor key to select the Navigation tab. Select Routes and press the RIGHT Cursor key to display the Routes submenu.

Create a route: From the Routes submenu, select Create and press the RIGHT Cursor key. A Route Edit screen will be displayed with an empty route. You can name the route, add waypoints to the route from the list of all waypoints, and order the waypoints in the route using the Cursor keys.

Edit a saved route: From the Routes submenu, select Edit and press the RIGHT Cursor key. A Route Edit screen will be displayed. Select the route you wish to edit and press the RIGHT Cursor key. Re-name the route or change, delete or re-order the waypoints used in the route.

Delete a saved route: From the Routes submenu, select Delete and press the RIGHT Cursor key. Select the route you wish to delete and press the RIGHT Cursor key. You will be asked to confirm your choice by pressing the RIGHT Cursor key again before the route is deleted.

Travel a saved route: From the Routes submenu, select Travel and press the RIGHT Cursor key. A list of saved routes will appear. Select the route you wish to travel and press the RIGHT Cursor key to make this route the current route and begin navigation. You may also travel the route in either forward or reverse order.

Route Info: From the Routes submenu, select Info and press the RIGHT Cursor key. A list of saved routes will appear. Select the route for which you want information, and press the RIGHT Cursor key. The list of waypoints in the route will be shown, with the distance and bearing from each waypoint to the next, as well as the distance and bearing from the current position to the first waypoint in the route.

SAVE OR CLEAR A CURRENT TRACK

(987c SI Combo models only)

Save the current track: From the Navigation X-Press™ Menu, select Save Current Track and press the RIGHT Cursor key. The track will remain on the display, but will change from black to gray. To remove the track completely from the display, see Edit, Delete or Hide Saved Tracks.

NOTE: When you save a track, a name is automatically assigned. The track name consists of a date/time stamp, but can be re-named later (see Edit, Delete or Hide Saved Tracks).

Clear the current track: From the Navigation X-Press™ Menu, select Clear Current Track and press the RIGHT Cursor key. The track will be removed from the display and discarded.

EDIT, DELETE OR HIDE SAVED TRACKS

(987c SI Combo models only)

Display the Tracks Submenu: From any view, press the MENU key twice to display the Main Menu System, then use the RIGHT Cursor key to select the Navigation tab. Select Tracks and press the RIGHT Cursor key to display the Tracks submenu.

Edit a saved track: From the Tracks submenu, select Edit and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to edit and press the RIGHT Cursor key. When the Edit Track dialog box appears, use the Cursor keys to move between fields. In the Track Name field, the UP and DOWN Cursor keys change the letter or number. All upper and lower case letters are available, as well as digits 0-9 and some punctuation characters. You can exit the Track Name field with the LEFT and RIGHT Cursor keys or by pressing the EXIT key. Select Save and press the RIGHT Cursor key to save your changes.

Delete a saved track: From the Tracks submenu, select Delete and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to delete and press the RIGHT Cursor key. You will be asked to confirm deletion before the track is actually deleted.

Hide or display a saved track: From the Tracks submenu, select Visibility and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to hide or display and use the Cursor keys to select Hidden or Visible. Press the EXIT key to return to the Tracks submenu.

45

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Page Thank You Table of Contents Sonar Menu Tab Menu System Start-Up Options MenuSonar X-Press Menu Side Imaging X-Press MenuSetup Menu Tab Alarms Menu TabContact Humminbird Views Menu Tab Accessories Menu Tab TroubleshootingDualbeam Plus Sonar Series IntroductionHOW the 900 Series Works Side Imaging SonarMulti-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD SlotInstallation Overview Accessory BUSControl Head Installation 900 Series has a wide variety of configurationsAccessory Bus Gimbal Mounting the Control Head Mounting Screws Washer Speed Communications Transducer Cable Collector Insert Cables Routed Near Mounting BracketIN-DASH Mounting the Control Head Parts and tools specific to In-dash mounting areBack of Control Head Expansion ports use for future accessories Beginning of this procedure Connecting the Control Head Power Cable to the BoatTransducer Installation Transom Transducer Trolling Motor TransducerMotor Position Stepped Hull Transom Transducer InstallationNot a hull, motor, or other transducer, etc Without deadrise adjustmentBe fully tightened until all adjustments are made Headed pin can be inserted from either side of the bracketCompletely tighten Normal Cavitation Force is necessary to pivot the assemblyTrolling Motor Transducer Installation Hand-tighten only Test and Finish the Transducer InstallationTo the cable as shown Follow these steps to stem mount the GPS receiverAccess Under Mounting Location No Access Under Mounting LocationAccess Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation Speed Accessory InstallationHand tighten only Install the Speed accessoryRotating Retaining Axial Clip to Remove Paddlewheel Testing the System InstallationSeries 987c SI Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the Sonar DisplayUnderstanding Sonar History Real Time Sonar RTS WindowSonar Bottom Presentation KHz provides highest resolution with 160 total beam width Understanding Side ImagingKHz provides maximum coverage with 180 total beam width Topography Changes Bottom Return Triplog WHAT’S on the Side Imaging DisplaySide Imaging Technology HOW IT Works Side Imaging on the Water InterpretationSide Imaging Representation Submerged Ravine with Timber Submerged Swimming Pool Submerged Standing and Fallen Timber, Plus Bait FishMenu KEY POWER/LIGHT KEYKEY Functions View KEYInfo KEY View Preset KeysWAY Cursor Control KEY Exit KEYSonar views ViewsMARK/GOTO KEY Views available on your 900 Series areViews and Readouts Sonar ViewSonar View Sonar Zoom View Sonar Zoom ViewSide Imaging View Split Sonar ViewSide Imaging View Split Sonar ViewSide/Sonar Combo View SIDE/SONAR Combo ViewBird’s Eye View Chart/Bird’s Eye Combo ViewChart/Sonar View Chart View with Active CursorChart/Side Combo View CHART/SIDE Combo ViewNavigation Chart View with Cursor PresentWaypoints, Routes and Tracks WAYPOINTS, Routes and TracksNavigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Press Menu Menu SystemStart-Up Options Menu Sonar Tab, Normal Mode Sonar Tab, Advanced ModeSTART-UP Options Menu Normal Simulator System StatusSystem Status Self Test Accessory Test GPS Diagnostic ViewNormal Operation SimulatorAccessory Test Accessory Test ScreenGPS Diagnostic View Split Position To Adjust Split Screen PositionSonar X-PRESS Menu Active SideUpper Range To adjust the SensitivityTo adjust the Upper Range SensitivityChart Speed Lower RangeZoom Level Bottom Lock Bottom RangeSonar Colors Highlight Split Position on the Side Imaging X-Press Menu Side Imaging Views onlySide Imaging X-Press Menu SI Side SI SensitivitySI Range Highlight SI Colors on the Side Imaging X-Pressmenu SI ColorsNavigation X-PRESS Menu To change the SI ColorsTo Clear Current Track Save Current TrackClear Current Track To Save Current TrackRemove Target Cancel NavigationSave Current Route Skip Next WaypointOnly if a Grid is active Remove GridSonar Menu TAB To Remove a GridBeam Select Side View FrequencyFish ID+ Highlight Fish ID Sensitivity on the Sonar main menu To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or offZoom Width To change the RTS Window settingTo adjust the Bottom View Bottom ViewNoise Filter KHZ SensitivityDepth Lines Surface ClutterMAX Depth Water TypeColor BAR Navigation Menu TAB Temperature GraphTo change the display of the Temperature Graph Sonar View only, with Temperature inputTracks WaypointsRoutes Trackpoint Interval Chart OrientationNorth Reference Trolling Grid RotationDelete ALL NAV Data Track MIN DistanceMAP Datum Export ALL NAV DataMAP Borders Chart Menu TABChart Detail Level To change the Chart Detail Level settingSET Simulation Position LAT/LON GridSpot Soundings Shaded DepthClear MAP Offset Alarms Menu TABTo change the Map Offset setting SET MAP OffsetTemp Alarm Depth AlarmFish ID Alarm LOW Battery AlarmOFF Course Alarm Arrival AlarmDrift Alarm Highlight Alarm Tone on the Alarms main menu Alarm ToneSetup Menu TAB To change the Alarm Tone settingUnits Speed Units DepthUnits Temp Units DistanceLanguage User ModeTriplog Reset Restore DefaultsSelect Readouts Default Sonar ViewTemp Offset To change the Depth Offset settingTo change the Temp Offset setting Depth OffsetPosition Format Speed CalibrationLocal Time Zone Daylight Saving TimeTime Format Date FormatNmea Output To Change the View Status of Any View Views Menu TABTo turn Sonar on or off Following views are availableSeries Defaults to Simulator with a Transducer Attached Accessories Menu TABTroubleshooting Series Doesn’t Power UpControl head loses power at high speeds Display ProblemsBoat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appearsHumminbird Service Policy Year Limited WarrantyReturning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Area of Coverage SpecificationsTransducer Mounting Template XHS-9-SI-160-T Appendix aContact Humminbird
Top Page Image Contents