Humminbird 987C SI COMBO Save Current Route, Skip Next Waypoint, Cancel Navigation, Remove Target

Page 64

www98x Manual..reelsche531376-1 A.qxd m2/23/2005atic11:40..coAM mPage 64

SAVE CURRENT ROUTE

(Only when navigating)

Save Current Route allows you to save the current route being displayed. This menu choice will only appear when you are currently navigating a route.

To Save Current Route:

1.Highlight Save Current Route on the Navigation X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate saving the current route.

3.The Confirm dialog box will appear. To save the current route, press the RIGHT Cursor key once more. To cancel saving the current route, press the LEFT Cursor key.

SKIP NEXT WAYPOINT

(Only when navigating)

Skip Next Waypoint removes the next waypoint from the current route. This menu choice will only appear when you are currently navigating a route.

To Skip Next Waypoint:

1.Highlight Skip Next Waypoint on the Navigation X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate skipping the next waypoint.

3.The Confirm dialog box will appear. To skip the next waypoint, press the RIGHT Cursor key once more. To cancel skipping the next waypoint, press the LEFT Cursor key.

CANCEL NAVIGATION

(Only when navigating)

Cancel Navigation discards the current route and exits Navigation Mode. This menu choice will only appear when you are currently navigating a route. This will not delete a previously-saved route.

To Cancel Navigation:

1.Highlight Cancel Navigation on the Navigation X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate canceling navigation.

3.The Confirm dialog box will appear. To cancel navigation, press the RIGHT Cursor key once more. To avoid canceling navigation, press the LEFT Cursor key.

REMOVE TARGET

(Only if a Target is active)

Remove Target removes the waypoint target from the display. This menu choice will only appear when a target has already been applied to a waypoint.

To Remove a Target:

1.Highlight Remove Target on the Navigation X-Press™ Menu.

2.Use the RIGHT 4-WAY Cursor Control key to remove the target.

58

Image 64

Contents Page Thank You Table of Contents Menu System Start-Up Options Menu Sonar X-Press MenuSide Imaging X-Press Menu Sonar Menu TabAlarms Menu Tab Setup Menu TabViews Menu Tab Accessories Menu Tab Troubleshooting Contact HumminbirdSeries Introduction HOW the 900 Series WorksSide Imaging Sonar Dualbeam Plus SonarMULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD SlotAccessory BUS Installation Overview900 Series has a wide variety of configurations Control Head InstallationAccessory Bus Gimbal Mounting the Control Head Mounting Screws Washer Cables Routed Near Mounting Bracket Speed Communications Transducer Cable Collector InsertParts and tools specific to In-dash mounting are IN-DASH Mounting the Control HeadBack of Control Head Expansion ports use for future accessories Connecting the Control Head Power Cable to the Boat Beginning of this procedureTransom Transducer Trolling Motor Transducer Transducer InstallationMotor Position Transom Transducer Installation Stepped HullWithout deadrise adjustment Not a hull, motor, or other transducer, etcHeaded pin can be inserted from either side of the bracket Be fully tightened until all adjustments are madeCompletely tighten Force is necessary to pivot the assembly Normal CavitationTrolling Motor Transducer Installation Test and Finish the Transducer Installation Hand-tighten onlyFollow these steps to stem mount the GPS receiver To the cable as shownNo Access Under Mounting Location Access Under Mounting LocationAccess Under Mounting Location Speed Accessory Installation Finish Routing the Cable and Check GPS Receiver OperationInstall the Speed accessory Hand tighten onlyTesting the System Installation Rotating Retaining Axial Clip to Remove PaddlewheelPowering UP the Control Head Series 987c SI Combo Title ScreenWHAT’S on the Sonar Display TriplogReal Time Sonar RTS Window Understanding Sonar HistorySonar Bottom Presentation Understanding Side Imaging KHz provides highest resolution with 160 total beam widthKHz provides maximum coverage with 180 total beam width WHAT’S on the Side Imaging Display Topography Changes Bottom Return TriplogSide Imaging on the Water Interpretation Side Imaging Technology HOW IT WorksSide Imaging Representation Submerged Ravine with Timber Submerged Standing and Fallen Timber, Plus Bait Fish Submerged Swimming PoolPOWER/LIGHT KEY KEY FunctionsView KEY Menu KEYView Preset Keys WAY Cursor Control KEYExit KEY Info KEYViews MARK/GOTO KEYViews available on your 900 Series are Sonar viewsSonar View Views and ReadoutsSonar View Sonar Zoom View Sonar Zoom ViewSplit Sonar View Side Imaging ViewSplit Sonar View Side Imaging ViewSIDE/SONAR Combo View Side/Sonar Combo ViewChart/Bird’s Eye Combo View Bird’s Eye ViewChart View with Active Cursor Chart/Sonar ViewCHART/SIDE Combo View Chart/Side Combo ViewChart View with Cursor Present NavigationWAYPOINTS, Routes and Tracks Waypoints, Routes and TracksNavigate to a Waypoint or Position Chart View with Grid Chart View with TargetADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Menu System Press MenuSonar Tab, Normal Mode Sonar Tab, Advanced Mode START-UP Options MenuNormal Simulator System Status Start-Up Options MenuSelf Test Accessory Test GPS Diagnostic View Normal OperationSimulator System StatusAccessory Test Screen Accessory TestGPS Diagnostic View To Adjust Split Screen Position Sonar X-PRESS MenuActive Side Split PositionTo adjust the Sensitivity To adjust the Upper RangeSensitivity Upper RangeLower Range Chart SpeedZoom Level Bottom Range Bottom LockSonar Colors Side Imaging Views only Highlight Split Position on the Side Imaging X-Press MenuSide Imaging X-Press Menu SI Sensitivity SI SideSI Range SI Colors Navigation X-PRESS MenuTo change the SI Colors Highlight SI Colors on the Side Imaging X-PressmenuSave Current Track Clear Current TrackTo Save Current Track To Clear Current TrackCancel Navigation Save Current RouteSkip Next Waypoint Remove TargetRemove Grid Sonar Menu TABTo Remove a Grid Only if a Grid is activeSide View Frequency Beam SelectFish ID+ To change the Fish ID Sensitivity setting Fish ID SensitivityTo turn Fish ID+ on or off Highlight Fish ID Sensitivity on the Sonar main menuTo change the RTS Window setting To adjust the Bottom ViewBottom View Zoom WidthKHZ Sensitivity Depth LinesSurface Clutter Noise FilterWater Type MAX DepthColor BAR Temperature Graph To change the display of the Temperature GraphSonar View only, with Temperature input Navigation Menu TABWaypoints TracksRoutes Chart Orientation North ReferenceTrolling Grid Rotation Trackpoint IntervalTrack MIN Distance MAP DatumExport ALL NAV Data Delete ALL NAV DataChart Menu TAB Chart Detail LevelTo change the Chart Detail Level setting MAP BordersLAT/LON Grid Spot SoundingsShaded Depth SET Simulation PositionAlarms Menu TAB To change the Map Offset settingSET MAP Offset Clear MAP OffsetDepth Alarm Fish ID AlarmLOW Battery Alarm Temp AlarmArrival Alarm OFF Course AlarmDrift Alarm Alarm Tone Setup Menu TABTo change the Alarm Tone setting Highlight Alarm Tone on the Alarms main menuUnits Depth Units TempUnits Distance Units SpeedUser Mode Triplog ResetRestore Defaults LanguageDefault Sonar View Select ReadoutsTo change the Depth Offset setting To change the Temp Offset settingDepth Offset Temp OffsetSpeed Calibration Local Time ZoneDaylight Saving Time Position FormatDate Format Time FormatNmea Output Views Menu TAB To turn Sonar on or offFollowing views are available To Change the View Status of Any ViewAccessories Menu TAB TroubleshootingSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer AttachedDisplay Problems Control head loses power at high speedsFinding the Cause of Noise Other electronic devicesNoise re-appears Boat’s engineYear Limited Warranty Humminbird Service PolicySeries Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Specifications Area of CoverageAppendix a Transducer Mounting Template XHS-9-SI-160-TContact Humminbird