Furuno FR-2155 manual Connection of display unit to control head, Underside

Page 20

P312 FX Connector

KB	BOTTOM

PLATE

Upset Screw

M6X12 (2 pcs.)

KB Clamp

Handle

KB Fixing Plate

Screw

M4X8 (8 pcs.)

Lay cable in slot.

J312	J314	(underside)
		(underside)
	(underside)

Earth Wire

P314 XH3P

Replace with	Spacer Pan-head Screw M4X8 (2 pcs.)
cable assy. in	Be careful not to pinch cable between
kit.	KB clamp and spacer.
	Figure 1-15 Control head

Connection of display unit to control head

1.Attach the handle to the handle plate, using the screws for the handle and bottom cover of the control head.

2.Attach the handle plate to location where the KB arms were fastened.

3.Pull the monitor toward you until you hear click.

4.Lead in the cable assy. (option) from the rear entrance of the display unit. See Chapter 2.

5.Raise the monitor and fix the stay.

6.Inside the display unit, fasten ground wire of the cable assembly with an M4 screw on the chassis.

7.Plug in two connectors of connection cable (P412, J583: See illustration on the previous page.)

1-12

Image 20

Contents Marine Radar B . N o . I M E 3 4 6 7 0 H Safety Instructions Use only the specified power cable Table of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No Qty RemarksSystem Configuration Data SentencesScanner Unit Mounting considerationsRemounting the synchronous gear magnet Scanner unit assembling Apply silicone sealant here Ring Choke grooveScanner unit mounting Mounting of scanner unit Mounting procedure Display UnitBefore mounting the display unit Tabletop mountingStay Setting catch to hole in stay Console type mounting Separating the control headSeparate Control Head Kit Type OP03-151, No Control head modification procedure 14 Removing the control headConnection of display unit to control head Underside15 How to attach KB fixing plate Attachment of hoodPower Supply Units Fabricating signal cable S03-80 PreparationsScanner unit, cover opened Fabricating signal cable 250V-MPYCY-16 JIS cable Fabrication of signal cable 250V-MPYCY-16When the de-icer is installed Fixing the scanner coverFabricating the power cable DPYCY-3.5 DPYCY-3.5Cable fed from back of display unit default Leading in cables to the display unitCable fed from outside display unit Cables fed from bottom of display unitConnections 12 Display unit, inside viewConnectors on the INT Board Connectors on the INT BoardChanging AC Power Specification of Display Unit How to attach NH connectorPower supply unit PSU-004 Thermal relay in power control unit PSU-004Power supply unit PSU-001 16 Fabrication of power cable and signal cableTuning Initialization Accessing Menus for Initialization and AdjustmentAdjusting Video Signal Level Restoring default settingsHeading Alignment Picture appears Deviated counterclockwiseAdjusting Sweep Timing Suppressing Main BangAntenna switch in tuning compartment Confirming Magnetron Heater VoltageScanner unit, power supply unit PSU-001 Initial Setting Menus Press Radar Menu 0 0 0Initial SETTING3 menu Initial SETTING1 menuInitial SETTING2 menu Initial SETTING4 menu OWN Ship Information menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8INT Board Default setting Connection of external power supplyDIP switch, jumper wire settings Setting method 1 by gyrocompass specifications Gyrocompass type FrequencySetting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5Setting the heading readout on the radar display SW1Installation of the ARP board ARP Board ARP-26ARP board adjustment ARP Board 18P9002BFinal check ARP Board ARP-26RP Board RP-26 Table top/console type10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no13 Display pedestal, front view Performance Monitor PM-30 Necessary parts PM-30 and OP03-150 Code noNecessary parts OP03-156 Code no Alarm KitProcedure 16 Display unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page