Furuno FR-2155 manual Separate type control head, Necessary parts RP-26-Z-2E Code no

Page 54

10.Fasten the front panel on the display pedestal.

11.Retract the stay to close the display unit. 12.Fasten the right arm cover.

Separate type control head

Necessary parts: RP-26-Z-2E (Code no. 008-491-400)

Name	Type	Qty	Code No.

Card Case Assy.	–	1	–

RP Board	14P0298	1	008-487-640

Pan Head Screw B	M4x8 C2700W	1	000-881-445

Pan Head Screw B	M3x8 C2700W	2	000-881-404

Pan Head Screw A	M2.6x5 C2700W	2	000-800-973

1.Lift the monitor. See Chapter 1 for instructions.

2.Fasten the mounting base with one M4 x 8 screw as below.

Fasten with

M4 x 8 screws.

Fasten with M3 x 8 screws (2 pcs.)

Figure 4-12 Display unit, inside view

3.Fix the mounting base to front panel with two M3 x 8 screws.

4.Set the M-card case lid to the hole in the front panel and fix with two M2.6 x 5 screws.

4-12

Image 54

Contents Marine Radar B . N o . I M E 3 4 6 7 0 H Safety Instructions Use only the specified power cable Table of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No Qty RemarksSystem Configuration Data SentencesScanner Unit Mounting considerationsRemounting the synchronous gear magnet Scanner unit assembling Apply silicone sealant here Ring Choke grooveScanner unit mounting Mounting of scanner unit Before mounting the display unit Mounting procedureDisplay Unit Tabletop mountingStay Setting catch to hole in stay Console type mounting Separating the control headSeparate Control Head Kit Type OP03-151, No Control head modification procedure 14 Removing the control headConnection of display unit to control head Underside15 How to attach KB fixing plate Attachment of hoodPower Supply Units Fabricating signal cable S03-80 PreparationsScanner unit, cover opened Fabricating signal cable 250V-MPYCY-16 JIS cable Fabrication of signal cable 250V-MPYCY-16When the de-icer is installed Fixing the scanner coverFabricating the power cable DPYCY-3.5 DPYCY-3.5Cable fed from back of display unit default Leading in cables to the display unitCable fed from outside display unit Cables fed from bottom of display unitConnections 12 Display unit, inside viewConnectors on the INT Board Connectors on the INT BoardChanging AC Power Specification of Display Unit How to attach NH connectorPower supply unit PSU-004 Thermal relay in power control unit PSU-004Power supply unit PSU-001 16 Fabrication of power cable and signal cableAdjusting Video Signal Level Tuning InitializationAccessing Menus for Initialization and Adjustment Restoring default settingsHeading Alignment Picture appears Deviated counterclockwiseAdjusting Sweep Timing Suppressing Main BangAntenna switch in tuning compartment Confirming Magnetron Heater VoltageScanner unit, power supply unit PSU-001 Initial Setting Menus Press Radar Menu 0 0 0Initial SETTING1 menu Initial SETTING2 menuInitial SETTING3 menu Initial SETTING4 menu OWN Ship Information menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8INT Board Connection of external power supply DIP switch, jumper wire settingsDefault setting Setting method 1 by gyrocompass specifications Gyrocompass type FrequencySetting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP5Setting the heading readout on the radar display SW1Installation of the ARP board ARP Board ARP-26ARP board adjustment ARP Board 18P9002B Final check ARP Board ARP-26RP Board RP-26 Table top/console type10 Display pedestal Separate type control head Necessary parts RP-26-Z-2E Code no13 Display pedestal, front view Performance Monitor PM-30 Necessary parts PM-30 and OP03-150 Code noAlarm Kit ProcedureNecessary parts OP03-156 Code no 16 Display unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page