Furuno FAR-2157 installation manual Desktop mounting, Contents of desktop mounting kit FP03-09820

Page 16

Panel hook

Panel cover

Fixing screw

How to attach panel hook and panel cover

Note: If you need to remove the monitor unit from the console, remove the four panel covers with your fingernail and use two panel hooks supplied as accessories to lift the monitor unit.

Desktop mounting

Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the monitor unit on a desktop.

Contents of desktop mounting kit FP03-09820

Name

Type

Code No.

Qty

 

 

 

 

Hanger L

03-163-1111

100-305-141

1

 

 

 

 

Hanger R

03-163-1112

100-305-181

1

 

 

 

 

Hanger stay

03-163-1113

100-305-191

1

 

 

 

 

Hole plug

CP-30-HP-13

000-160-074-10

2

 

 

 

 

Snap button

KB-13, Black

000-570-276-10

4

 

 

 

 

Hex. bolt

M6×25

000-162-949-10

4

 

 

 

 

Hex. bolt

M10×30

000-162-884-10

2

 

 

 

 

Spring washer

M10

000-864-261

2

 

 

 

 

Flat washer

M10

000-864-131

2

 

 

 

 

1.Assemble two hangers and hanger stay with two hex bolts (M10×30), flat washers and spring washers and cover each hex bolt with hole plug.

2.Fix the above assembly to the mounting location with four hex bolts (M12, dockyard supply).

3.Fasten the monitor unit to the mounting hanger assembly with four hex bolts (M6×25, supplied).

4.Cover each hex bolt with a panel cover (4 pcs.).

5.Cover fixing holes for hand grips with snap buttons (4 pcs).

1-8

Page 15 Page 17
Image 16
Page 15 Page 17
Contents
Installation manual 00014869215 Safety Instructions Use only the specified power cables System Configuration IiiOptional equipment Standard supplyName Type Code No Qty Remarks Name Type Code No Remarks DVI-RGBThis page is intentionally left blank Antenna Unit Mounting considerationsSiting MountingHow to coat waveguide flange with silicon rubber Assembling the antenna unitName Type Qty How to hoist antenna unit How to attach hoisting ropes to antenna unitFastening antenna unit to the mounting platform How to mount the antenna unit Coat with anticorrosive sealantMonitor Unit Mounting procedureFlush mounting Contents of desktop mounting kit FP03-09820 Desktop mountingAttaching hand grips Control Unit Fixing with KB keyboard fixing plateMounting dimensions for control unit RCU-015/RCU-016 Mounting dimensions for control unit RCU-014Fixing without KB fixing plate Contents of flush mount kit for RCU-014/015/016 Connecting RCU-016 in series with RCU-014 Control unit RCU-014, inside viewChanging the cable entrance on control unit RCU-015/RCU-016 Changing cable entrance on control unit RCU-015/RCU-016Mounting dimensions for processor unit Processor UnitPower Supply Unit Mounting dimensions for power supply unitWiring Wiring OverviewFabricating signal cable RW-9600 Fabricating signal cable RW-9600Antenna unit, front view TB801 PCB 03P9436 Cable gland for signal cable RW-9600 How to wire Wago connector ProcedureHow to fasten coaxial conductor How to fabricate HV cable TYPCY-1.5 Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5Passing flat washer, etc. onto HV cable How to fabricate power cable TYPCY-2.5 Passing flat washer, etc. onto power cableFabricating the power cable DPYC-2.5 Fabricating power cable DPYC-2.5Fabricating power cable DPYC-2.5 Connection of cables Processor unit, rear viewCable XH10P-W-6P L=20/30M Cable XH10P-W-5P-A L=10/20/30MLocation of connectors Location of connectors inside the processor unitSignal cable RW-9600 Between antenna unit and processor unit Power cable TPYC-1.5Connection of Sub-display Port Conventional remote display FAR-2157Fabricating cable connected to terminal TB1, TB2, TB3 Power supply unit, inside viewTerminal TB1 cable DPYC-2.5 Armor Changing AC Power Specification Power supply Fuse Jumper connector P108Processor unit Processor unit, inside viewHow to adjust the overvoltage detection circuit Power supply unit Power Fuse Jumper connector P8Adjustments Initializing TuningHeading Alignment Heading alignmentFor Control Unit RCU-014 For Control Unit RCU-015Initialize menu Echo ADJ menuHow to access the Initialize Menu with Control Unit RCU-015 Adjusting Sweep Timing Examples of correct and incorrect sweep timingsSuppressing Main Bang Other Settings Echo menu settingBlind Sector 1 and Blind Sector Scanner menuANT SW and ANT Stopped Radar no and Radar Posn Installation menuOn Time and TX Time LENGTH/WIDTH, Scanner Posn and SUB Scanner Posn OWN Ship Info menuGPS 1 ANT Posn and GPS 2 ANT Posn ARP W/O Gyro Not shown on IMO radar Arpa Preset menuARP-related menus ANT Select EAV w/o Gyro Other menuOther menu This page intentionally left blank Installing the Gyro Converter board Gyro Converter GC-10Fixing Gyro Converter board inside the processor unit Connecting connector assemblies inside processor unit Wiring Wago connectorAttaching plastic cover for Gyro Converter board Connection of external power supply DIP switch, jumper wire settingsDefault setting Connection of external power supply to Gyro Converter boardJP1 Setting method 2 by make and model of gyrocompass JP1 JP2 JP3 JP4 JP564P1106 Gyro Converter boardSetting the heading readout on the radar display HDG menuFlush mounting dimensions for memory card interface unit Memory Card Interface UnitConnections Desktop mountOne memory card if unit and one processor unit One memory card if unit and multiple processor unitsType Code No Contents How to wire the DVI-RBG conversion board DVI-RGB Conversion KitProcessor unit, side view Processor unit bottom chassisConnecting wires to the housing BNC Connector Converter DVI-RGBInput Data Specifications Contents RemarksOutput IEC 61162 input sentence and priority IEC 61162 output sentenceSentence and order of priority Sentence45$545$5 #  76.+0 +26+10%1& 52 427 52 257 #%8 . . .   GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Marine RADAR/ARPA
Top Page Image Contents