Furuno 821, 841 manual Entering Initial Settings, Relative Bearing Alignment

Page 53

3)Press the cursor pad to select Installa- tion Setup 1 and press the [ENT] key.

 

 

INSTALLATION SETUP 1

 

Select

item and option

 

 

 

 

by ▲▼ keys.

 

 

 

 

1. Key Beep

OFF

ON

 

 

2. Hdg Sensor

MAG

GYRO

3. Ant on Tx

ROTATE

STOP

4.

Demo Display

OFF ON

 

 

5.

Antenna Unit

M841 MK2

M841

6.

Installation Setup 2

 

 

 

 

. . . . . . . . . . . . . . . . .

Press HM-OFF to temporarily hide menu.

<Press MENU for main menu.>

Figure 5-18 Installation setup menu 1

4)To display the Installation Setup 2 menu, press the cursor pad to select Installation Setup 2.

INSTALLATION SETUP 2

Select item and option by trackball.

1.Align Heading

2.Adjust Sweep Timing

3.On Hours 000019.8 H

4.Tx Hours 000016.0 H

. . . . . . . . . . . . . . . . .

Press HM-OFF to temporarily hide menu.

<Press MENU for main menu.>

Figure 5-19 Installation setup 2 menu

5.6 Entering Initial Settings

1)At the Installation Setup 1 menu, press the cursor pad to select Key Beep. (Key Beep turns on or off the buzzer which sounds when a key is pressed.)

2)Press the cursor pad to select OFF or ON.

3)Select Hdg Sensor.

4)Select type of heading sensor connected to the radar; MAGnetic compass or GYROcompass.

5) Press the [ENT] key.

Leave the menu open to complete the next several adjustments.

5.7 Relative Bearing Alignment

You have mounted the antenna unit facing straight ahead in the direction of the bow. Therefore, a small but conspicuous target dead ahead visually should appear on the heading mark (zero degrees).

In practice, you will probably observe some small error on the display because of the dif- ficulty in achieving accurate initial position- ing of the antenna unit. The following adjustment will compensate for this error, up to 360° degrees.

1)Identify a suitable target (for example, ship or buoy) at a range between 1/8 to 1/4 miles, preferably near the heading mark. To minimize error, keep echoes in the outer half of the picture by changing the range.

2)Display the Installation Setup 2 menu.

INSTALLATION SETUP 2

Select item and option by trackball.

1.Align Heading

2.Adjust Sweep Timing

3.On Hours 000019.8 H

4.Tx Hours 000016.0 H

. . . . . . . . . . . . . . . . .

Press HM-OFF to temporarily hide menu.

<Press MENU for main menu.>

Figure 5-20 Installation setup 2 menu

3)Select Align Heading and press the [ENT] key.

4)Press the cursor pad to bisect the target selected at step 2 with the EBL.

5)Press the [ENT] key,

42

Image 53
Contents Marine Radar First Edition AUG Electrical Shock Hazard Safety ArrangementsGround both the Display Unit and the Antenna Unit Useable EnvironmentTable of Contents Foreword FeaturesAntenna Unit SPECIFICATIONS- ModelTransceiver Module contained in radome Display UnitProtection features Power supply & power consumptionWarm-up time Modulator switching method VibrationReceiver front end MIC Michoeave IC Bandwidth 7 MHz Duplexer Ambiont temperatureInterface Nmea Model 821/841 Page Model 821/841 ConfigurationPrinciple of Operation How radar works Control Description OperationTurning the Radar On Off Display Indications and MarkersAdjusting Control Panel Brilliance Adjusting LCD Backlighting and Display ToneTransmitting Selecting the RangeSTC MAN Auto Adjusting GAIN, STC, A/C Rain and FTCAdjusting A/C Rain Tuning the ReceiverAdjusting FTC How to tune manuallyMeasuring the Bearing Measuring the RangeTarget on collision course with your vessel? Menu OperationMenu description 11 Display modes Selecting the Display ModeCU course-up Selecting the Presentation ModeWindow Display WPT-UP waypoint-up Guard AlarmGuard Suppressing Radar InterferenceSelecting Pulselength Suppressing Noise InterferenceOff Centering the Display Navigation Data Display Echo TrailsPress the Menu key Select Nav Data and press the ENT key Echo Stretch magnifying long range echoesWatchman Selecting Unit of Measurement for RangeSelecting Bearing Reference Displaying Navigation Data During Stand-by Erasing the Heading MarkerDeselecting Ranges Displaying Cursor Position, Range and Bearing to Cursor Visual Alarm IndicationsOutputting Cursor Position to Navigator Radar Wave and Radar Horizon Interpreting the DisplayTarget Properties and Radar Wave Reflection Super-refractionFalse Echoes Bearing ResolutionRange Resolution Multiple echoes Blind and shadow sectors Nautical Chart and Radar PictureSafety Information Maintenance & TroubleshootingForming any maintenance or Troubleshooting procedureReplacing the Fuse Preventative MaintenanceTroubleshooting table TroubleshootingSelf Test Self TestAntenna Unit Installation InstallationVent tube Removing packing materialsMounting platform How to fasten the radome base To the mounting platform Ships bow Removing packing materials 10 Antenna unit Model 841, inside view, shield cover removed 12 Optional mounting bracket installation for sailboat Display Unit Installation 13 How to mount the display unit 14 Display unit, rear view Procedure Option connectorInstallation Check List Displaying the Installation Menus Initial Adjustment of PictureRelative Bearing Alignment Entering Initial SettingsSweep Timing Closing the Installation MenusSignal cable connection Page Page Page Page Page Page Page