Battery-Biz 5150, 5170 Optional Installation of Deluxe Remote, To Mount the TruePower Inverter

O p t i o n a l R e m o t e I n s t a l l a t i o n

13

Optional Installation of Deluxe Remote

Step 3 - Use photocopy of the drill template below to mark (4) mounting holes and (2) cable thru holes. See illustration No. 1 for surface mount application.

- or -

Use drill template to mark and cut a 2-5/8" x 2-1/8" opening and (4) mounting holes. See illustration No. 2 for flush mount application.

Note: Use caution prior to drilling or cutting to ensure proper clearance from existing wiring and hardware.

Step 4- Assemble remote panel without snap on mounting covers. Place cable in socket on the back of remote and then thru the holes, align mounting holes and using a hand screwdriver, install the 4 stainless steel screws provided. Snap on mounting ear covers to complete installation.

Step 5- Run the remote cable, to the inverter- be careful of sharp objects.

Step 6- Plug the remote cable into the socket found on the previously installed backing plate. Your remote is now ready for use.

I n s t a l l a t i o n G u i d e l i n e s

6

Mounting your Inverter Continued

Fuses: As stated in this manual, for an ABYC E-11 compliant installation, this Inverter must be installed with an inline fuse in the positive (+) cable on the DC side of the inverter (between the battery and the inverter) at a distance of seven inches from the battery connection (Please see Specifications Table in this Manual for correct sizing).

If this external fuse blows, or if the breaker trips on the larger models, there is a short or overload in the DC wiring. Find and fix the problem before replacing the fuses or resetting the breaker. After replacing the fuse, reconnect the inverter.

The 2000 to 3000 watt True Power inverters are equipped with a magnetic breaker for the hardwired connection and a thermal breaker for the additional GFCI outlet on the unit. Again, all units should be serviced only by a professional qualified electrician, or more preferably by our factory service department. For any service issues, please call toll free 1-800- 824-0524.

To Mount the TruePower Inverter:

No.1 Surface Mount Installation

On Board	Deluxe Inverter
Solutions			Remote
A ProMariner Company
	DC	Inverter
	Input Voltage
	100%	Output Current
On		100%
Off
	0	0
Power
	Over Load	Over Temp

No. 2 Flush Mount Installation

			2-5/8
On Board	Deluxe Inverter
Solutions			Remote
A ProMariner Company
	DC		2-
			1/8
	Input Voltage	Inverter
	100%	Output Current
On		100%
Off
	0	0
Power
	Over Load	Over Temp

1.Turn the On/Off switch on the front panel of the inverter to Off position.

2.Select an appropriate mounting location and orientation.

3.Hold the inverter against the mounting surface, mark the position of the mounting screws, and then remove the inverter.

4.Drill pilot holes for the four mounting fasteners ( Use caution prior to drilling or cutting to ensure proper clearance from existing wiring and hardware).

5.Fasten the inverter to the mounting surface with four hardware fasteners.

Note: For the best load starting performance, the DC cables should be short and large as possible. A solid, low resistance connection to the DC power source is

2-5/8

TemplateDrill

2-1/8

important for proper operation of the TruePower Inverter. Using a smaller cable may cause the inverter to shut down under a heavy load.

Note: A ground stud can be found on the rear panel of the TruePower inverter as illustrated in “TruePower Overview” earlier in this manual. The ground stud must be connected to a grounding point, which will vary depending on where the TruePower inverter is installed. We recommend an #8 gauge AWG or larger copper wire. In a vehicle, please secure a ground wire from this stud to the chassis of your vehicle, keeping the distance of the ground as short as possible. In a boat, connect to the boat’s grounding system. In a fixed location connect the inverter’s ground stud to earth by connecting to a ground rod (a metal rod pounded into the earth) or other proper service entrance ground.

cut along line for flush mounting