Baja Marine 245 manual Hull Identification Number HIN, Manufacturer’s Certification

Page 6

Introduction

6.Hull Identification Number (HIN)

The “Hull Identification Number” located on the starboard side of the transom, is the most important identifying factor and must be included in all correspondence and orders. Failure to include it creates delays. Also of vital importance are the engine serial numbers and part numbers when writing about or ordering parts for your engine. Refer to the Engine Operator’s Manual for locations of engine serial numbers and record them for future reference.

Hull Identification Number Location

(Fig. iv.1)

HIN Number

7.Manufacturers Certification

As a boat manufacturer, Baja builds its products to guidelines established under the Federal Boat Safety Act of 1971. The Act is promulgated by the United States Coast Guard who has authority to enforce these laws on boat manufacturers that sell products in the United States. Baja ensures that all of its products comply with these laws.

The NMMA, National Marine Manufacturers Association, provides Baja with a third party certification. The NMMA is an organization that represents the marine industry and assists manufacturers, boat dealers, marinas, repair yards, and component suppliers in areas of legislation, environmental concerns, marine business growth, and state and federal government agency interaction. The third party certification that Baja participates in uses the well known Standards and Recommended

Practices of the ABYC, American Boat and Yacht Council.

Baja Marine Corporation participates extensively in the American Boat and Yacht Council which is a nonprofit organization that develops and publishes voluntary standards and recommended practices for boat and equipment design, construction, service, and repair. We utilize all applicable ABYC standards in the construction of our boats.

Finally, Baja sells their products world wide and as such must conform to the various rules and regulations required by other countries. Most notably, are the ISO standards in Europe which require the application of the CE (Common European) mark. This mark, much like the NMMA certification in the U.S., gives you, the boat owner, specific information concerning your craft.

8.Service, Parts and Repair for Your Boat

When your boat needs service, parts or repair, take it to an authorized Baja® Marine dealer. To find a dealer in your area visit our website at www. bajamarine.com or call:

Domestic/International 1-865-971-6270 Fax: 1-865-971-6716

To find repair and parts facilities for the equipment installed on your boat, refer to the manual for that component.

If an issue is not handled to your satisfaction:

1.Discuss any warranty-related issues directly with the service manager of the dealership or your sales person. Give the dealer an opportunity to help the service department resolve the matter for you.

2.If an issue arises that has not been resolved to your satisfaction by your dealer, contact Baja® Marine at 1-865-971-6270 and ask to speak with a customer service representative.

iv

245 Performance®

Image 6
Contents Baja Marine PerformanceFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Service, Parts and Repair for Your Boat Hull Identification Number HINManufacturer’s Certification About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsLegally Mandated Minimum Required Equipment Carbon MonoxideFire Extinguishing System Carbon Monoxide Monitor Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationLoad Capacity Power Capacity StabilityMaintain Control WeatherGeneral Considerations Chart Your Course Water Sports SwimmingSkiing Medical Emergency Emergency SituationsGeneral Water RescueFire Flooding, Swamping and CapsizingCollisions and Leaking Grounding Safety HotlinesInternational Requirements Propulsion, Control or Steering FailureExcessive Noise Environmental ConsiderationsWaste Disposal Wake/WashNautical Terms Key to Symbols on Controls & Prints This Page Intentionally Left Blank Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger LocationsPerformance Specifications Basic Boat Dimensions and Clearances Metric Propulsion SystemPropellers General Deck Layout Power Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trailer Switch Trim TabsImportant Gauges Ignition Shutdown SwitchEngine Alarm System Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EnginePower Steering System Steering SystemFuel & Oil Spillage Bilge & Underwater GearBilge Bilge PumpsBilge Blowers Maintenance and ServiceEngines and Stern Drive Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Direct Current DC Electrical SystemsElectrical Systems BatteriesElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump Drive Pump w/ K-Plane Trim Tabs Ignition Switch Switch Panel Wire Information FIG ATTaCh 4 aWg RED Wire To fUsE PanEl MaInThis Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsAutomatic Fire Extinguisher System Option CanvasSwim Platform w/ Ladder Optional Depth Finder OptionalHorn Stereo SystemHead Systems Exhaust SystemsRequirements for Operators Required Inspection, Service Maintenance Summary Guide For Inspection, Service and MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaTopside and Supplies Winterization Checklist for Boats Stored on LandBatteryies Boat StorageFuel System Fitting Out After StorageFuel Systems MiscellaneousPower Steering System Maintenance Security ConsiderationsQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Stains & Scratches Paint Cleaning Agents & Other SubstancesCare & Refinishing Fiberglass & GelcoatAcrylic Plastic Sheeting Plastic Glass Permanently Moored or Docked BoatsTopside Areas Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Performance