Ingersoll-Rand LM2350E-XX-B specifications Operating and Safety Precautions, PM Cylinder, Adapter

PARTS LIST / LM2350E-XX-B

Item	Description (size in inches)		Qty	Part No.	[Mtl]
1	Carriage Bolt (1/4” - 20 x 9” long)		(4)	94333	[C]
2	Upper Cap		(1)	94390	[Z]
n 3	Track Gasket		(2)	94392	[B]
4	Sleeve		(2)	94316	[Br]
n 5	“O” Ring (1/16” x 11/16” o.d.)		(4)	Y325-15	[B]
n 6	“O” Ring (1/8” x 3/4” o.d.)		(4)	Y325-206	[B]
7	Spool		(2)	94310	[D]
n 8	“U” Cup (1/8” x 3/4” o.d.)		(2)	Y240-7	[B]
n 9	“O” Ring (.106” x .587” o.d.)		(2)	15066-PM	[B]
10	Cylinder		(1)	94306	[A]
11	Adapter	models LM2350E-X1-B	(1)	94384	[C]
		models LM2350E-X2-B	(1)	94384-1	[C]
n 12	“O” Ring (1/16” x 3/4” o.d.)		(1)	Y325-16	[B]
n 13	“O” Ring (1/16” x 7/16” o.d.)		(1)	Y325-11	[B]
14	Muffler Housing		(1)	94443	[A]
15	Foam Liner		(2)	94402
16	Edge Trim		(2)	94378-1	[N]
18	Retaining Ring		(1)	94406	[C]
19	Washer		(1)	94515	[C]
n 20	“U” Cup (3/16” x 3” o.d.)		(2)	94518	[B]
21	Piston		(1)	94403	[D]
23	Piston Adapter		(1)	94388	[C]
n 24	“O” Ring (3/32” x 1” o.d.)		(1)	Y325-117	[B]
25	Dowel Pin (1/4” o.d. x 7/8” long)		(1)	Y148-37	[C]
26	Washer		(1)	94785	[C]
n 27	“O” Ring (3/32” x 11/16” o.d.)		(1)	Y325-112	[B]
28	Spring		(1)	94705	[C]
n 29	Rod Seal		(1)	93921	[U]
30	Base	models LM2350E-X1-B	(1)	67188	[C/Z]
		models LM2350E-X2-B	(1)	67188-1	[C/Z]
31	Nut (1/4” - 20)		(4)	93828	[SS]
32	Ground Screw (#10 - 32 x 1/4”)		(1)	93005	[C]
n 33	Gasket		(1)	70834	[Co]
34	Extension Tube
	- LM2350E-2X-B (7.531’’)		(1)	94401-2	[C]
	- LM2350E-3X-B (20.281’’)		(1)	94401-3	[C]
	- LM2350E-4X-B (28.781’’)		(1)	94401-4	[C]

Item	Description (size in inches)	Qty	Part No.	[Mtl]
	- LM2350E-6X-B (10.281’’)		94401-6	[C]
		(1)
	- LM2350E-7X-B (18.531’’)	(1)	94401-7	[C]
	- LM2350E-8X-B (27.781’’)	(1)	94401-8	[C]
n 35	Gasket	(1)	70837	[Co]
36	Piston Rod	(1)	94385	[C]
37	Pin	(1)	94786	[C]
n 38	Cotter Pin (1/16” x 1/2” long)	(1)	Y15-21	[C]
39	Connector - LM2350E-2X-B (3.457”)	(1)	94340-2	[C]
	- LM2350E-3X-B (16.207”)	(1)	94340-3	[C]
	- LM2350E-4X-B (24.707”)	(1)	94340-4	[C]
	- LM2350E-6X-B (6.207”)	(1)	94340-6	[C]
	- LM2350E-7X-B (14.457”)	(1)	94340-7	[C]
	- LM2350E-8X-B (27.707”)	(1)	94340-8	[C]
	Piston & Tube Ass’y (includes 40 - 44)	(1)	71523-1
40	Lower Suction Tube	(1)		[C]
41	Plunger	(1)		[C]
42	Ball Stop	(1)	83276	[C]
43	Ball (9/32” dia.)	(1)	Y16-209	[C]
44	Adapter	(1)	70817-11	[C]
n 45	Guide Washer	(1)	71524-1	[Co]
46	Spacer	(1)	72392-1	[C]
47	Retaining Ring (.763” o.d.)	(1)	Y147-68	[C]
48	“U” Cup (3/16” x 11/16” o.d.)	(1)	Y186-4	[B]
49	Guide Spacer	(1)	76705	[T]
50	Valve Body	(1)	76704	[SH]
n	Foot Valve Ass’y (includes 47 - 50)	(1)	60940
n 51	Gasket	(1)	F21-65	[Co]
52	Valve Seat	(1)	6797	[C]
53	Primer Rod	(1)	94446	[C]
n 54	Retainer Ring	(1)	94397	[C]
55	Primer	(1)	94400	[C]
56	Primer Tube	(1)	94399	[C]
: 57	Bung Assembly (includes 58)	(1)	67145-2	[ZA]
: 58	Thumb Screw (1/4” - 20 x 1”)	(3)	Y66-59-C	[C]

:Not included with models LM2350E-6X-B

n Gadus S2 U1000 Grease Packet	(1)	94833
n Parts in Repair Kit		637227-B

OPERATING AND SAFETY PRECAUTIONS

WARNING EXCESSIVE INLET PRESSURE. Can cause ex-

plosion resulting in severe injury or death. Do not exceed maxi- mum operating pressure of 7500 p.s.i. (517.2 bar) at 150 p.s.i. (10.3 bar) inlet air pressure. Do not run pump without using a regulator to limit air supply pressure to the pump.

WARNING EXCESSIVE MATERIAL PRESSURE. Can cause

equipment failure resulting in severe injury or property dam- age. Do not exceed the maximum material pressure of any component in the system.

Replacement warning label is available upon request, PN \ 94520.

PUMP RATIO X	=	MAXIMUM PUMP
INLET PRESSURE TO PUMP MOTOR		FLUID PRESSURE

Pump ratio is an expression of the relationship between the pump motor area and the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is supplied to the motor of a 50:1 ratio pump it will develop a maximum of 7500 p.s.i. (517.2 bar) fluid pressure (at no flow) -- as the fluid control is opened, the flow rate will increase as the motor cycle rate increases to keep up with the demand.

NOTICE: Thermal expansion can occur when the fluid in the materi-

al lines is exposed to elevated temperatures. Example: Material lines located in a non-insulated roof area can warm due to sunlight. Install a pressure relief valve in the pumping system.

Page 2 of 4 LM2350E-X-B