Ingersoll-Rand 67314-B specifications Service Kits, Specifications, General Description

Page 1

OPERATOR’S MANUAL

67314-B

INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, PARTS, TROUBLESHOOTING

RELEASED: 11-10-06

 

 

REVISED: 5-17-10

4.125 SQ.” MOTOR

67314-B

(REV. 03)

 

65 - 2000 P.S.I. RANGE

HYDRAULIC POWER MOTOR

 

 

 

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Use only genuine ARO® replacement parts to assure compat- ible pressure rating and longest service life.

637450 pump repair kit, includes the necessary soft parts for normal service of the entire pump.

SPECIFICATIONS

Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67314-B

Type . . . . . . . . . . . . . . . . . . . . Hydraulic Operated Power Motor Motor Size . . . . . . . . . . . . . . . . . . . . . . . . . . 4.125 sq.” (26.6 sq. cm) Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6” (152 mm)

Hydraulic Inlet (female) . . . . . . . . . . . . . 1/2 - 14 N.P.T.F. - 2 Hydraulic Outlet (female) . . . . . . . . . . . 3/4 - 14 N.P.S.M. Pump Construction . . . . . . . . . . . . . . . . . Carbon Steel Dimension “A” . . . . . . . . . . . . . . . . . . . . . . 20-13/32” (518.2 mm) Dimension “B” . . . . . . . . . . . . . . . . . . . . . . 15-11/16” (397.8 mm) “C”Weep Hole . . . . . . . . . . . . . . . . . . . . . . 1/8 - 27 N.P.T.F. - 1 Motor Diameter. . . . . . . . . . . . . . . . . . . . . 8” (203.2 mm) Maximum Temperature Limits . . . . . . 130° F (54° C) Mounting Bracket available . . . . . . . . 95933

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.75 lbs (17.1 kgs)

PERFORMANCE

Inlet Pressure Range . . . . . . . . 65 - 2000 p.s.i. (4.5 - 137.9 bar) Required H-power @ 50 c.p.m. . . . . . . 3.2 @ 1200 (82.8 bar) Hydraulic flow required @ 50 c.p.m. 11 g.p.m. (41.6 l.p.m.) Maximum Thrust generated . . . . . . . . 8250 lbs Maximum recommended cycles / minute. . . . . . . . . 50 Noise Level . . . . . . . . . . . . . . . . . . . . . . . . . N/A

GENERAL DESCRIPTION

The 4.125 square inch hydraulic motor is a general purpose power unit and is used on many ARO industrial 2-ball, 4-ball and chop-check pumps. It utilizes tie rod type construction for serviceability and connects to the various lower pump ends by tie rods.

Due to frictional losses in the system, a greater horsepower is required to run the motor. Power supplies generating less than shown as required in the Performance Specifications above will work with the motor but at a reduced pressure or cycle rate.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 276-4658 FAX (800) 266-7016

© 2010

CCN 15267008

Hydraulic Inlet

Hydraulic Outlet

B

A

C

Figure 1

OPERATING AND SAFETY PRECAUTIONS

WARNING READ THE GENERAL INFORMATION MAN- UAL INCLUDED FOR ADDITIONAL OPERATING AND SAFETY PRECAUTIONS AND OTHER IMPORTANT IN- FORMATION.

WARNING EXCESSIVE MATERIAL PRESSURE. Can cause equipment failure resulting in severe injury or prop- erty damage. Do not exceed the maximum material pressure of any component in the system.

WARNING A pressure relief valve must be used to pre- vent over-pressurization of the system and possible component rupture.

WARNING Excessive hydraulic oil temperature can cause fire. The unit is rated for operation up to 130° F (54° C). Be sure return lines are sized larger than sup- ply lines and similarly pressure rated.

WARNING Never service or disassemble the unit or unit components without relieving hydraulic system pressure ￿rst. The high pressures involved could cause serious injury.

NOTE: If this pump was purchased separately (not part of a system), consult your sales representative for com- patible dispensing accessories which will best match the application. All accessories must be able to withstand the maximum pressure developed by the pump.

A replacement warning label is available upon request, pn \ 94576.

www.ingersollrandproducts.com

Image 1
Contents Specifications Service KitsOperating and Safety Precautions General DescriptionService Installation Trouble ShootingIf the pump will not cycle or will not deliver material Leakage from weep hole in retainerTorque Requirements 3b ‰ 27  31 30Lubrication / Sealants Removal of 4 sleeve and spool assembly Disassembly ReassemblyRemoval of 22 piston rod