Grizzly H8068 owner manual Finishing Body, To finish the guitar body

Page 11

Finishing Body

This guitar looks incredible with a clear finish to highlight the wood grain patterns. The surface can be stained prior to finishing or a transparent pigment can be added to the finish. These instruc- tions guide you through a very basic finishing pro- cess. Books describing different guitar finishing techniques are available through luthier supply catalogs, or through your local library. Clear finish materials and books on finishing can be ordered through Grizzly Industrial. Finishing a guitar is a difficult task. If you are unsure of your skills; do your research, practice on scrap wood, or take it to a professional.

Components and Hardware Needed:

Qty

Guitar Body

1

To finish the guitar body:

 

1.Mask off the neck pocket. Press the masking tape tight against the edges of the pocket so the finish does not seep under the tape.

2.Screw through the neck pocket screw holes into a long piece of wood to use for a handle during spraying. Drill a hole in the end of the handle for hanging from a hook.

3.Wipe the entire guitar body with a tack cloth or a soft clean rag to remove any dust.

4.Thread the hook through the temporary han- dle and hang the body in the finish room.

5.Apply several thin coats of the finish, follow- ing the manufacturer's instructions. Multiple thin coats usually produce a better quality finish than one heavy coat.

6.Sand the entire body with #400 grit wet and dry sandpaper after at least three coats of finish have been applied. DO NOT sand through the finish—be especially careful on the edges.

7.Apply more finish, sanding between coats, until the finish is the desired thickness.

Note: If finishing with a solid color, you may wish to apply several coats of a clear finish over the top, sanding between coats, to add depth to the finish.

8.When the final coat has dried at least a week, preferably a month, remove the tem- porary handle and masking.

9.Wet sand the finish using #600 grit wet and dry sandpaper on a sanding block, followed with #1000 grit wet and dry sandpaper.

10.Buff the finish by hand or with a buffer, start- ing with a medium polish and work up to a high gloss polish.

Note: If using a buffing machine, be extreme- ly careful to avoid going through the finish, especially on the edges.

NOTICE

Dust particles suspended in the air will settle on wet finishes, causing less than sat- isfactory results. To avoid this problem:

Leave the finishing room undisturbed for 24 hours prior to applying the fin- ish.

Avoid making unnecessary movements upon entering the finish room.

Apply the finish to the desired guitar parts and immediately leave the finish room.

DO NOT return to the room until the specified drying time has elapsed.

H8068 Telecaster® Style Kit

-9-

Image 11
Contents Model H8068 Telecaster Style KIT Page Table of Contents Safety Contact Info IntroductionForeword Inventory Parts InventoryRecommended Tools & Supplies Supplies/ToolsIdentification Model H8068 headstock features H8068 Telecaster Style KitComponents and Hardware Needed Qty AssemblySanding Body Sanding NeckTo finish the guitar neck Finishing NeckTo finish the guitar body Finishing BodyTo determine neck mounting hole depth Mounting NeckTo mount the neck to the guitar body To mount the neck to the body Another way to determine neck mounting hole depth OptionalTo drill mounting holes in the neck To position the pick guard, control plate and bridge Positioning Pick Guard, Control Plate BridgeInto the control plate cavity Body, go to Installing Ferrules,Go to Mounting Tuners on Installing FerrulesTo install the ferrules Mounting Tuners To install the tunersTo wire the pickups Wiring PickupsTo position the ground wire under the bridge Installing Output JackInstalling Bridge Control Plate To install the output jackTo attach the strap buttons to the guitar Installing NutTo install the nut Strap ButtonsWinding Strings To install strings through the bodyString Retainers To install the strings using only the bridgeTo install the string retainer General SetupNeck Adjustment To adjust the bow of the guitar neckTools Needed Qty To adjust the string heightString Height To tune the guitar Pickup Height TuningTo measure the string height at the pickup To set the intonation Setting IntonationReference Info AccessoriesModel H6976 H6976-The Fender TelecasterPickup Electrical ComponentsTo Bridge Ground Tone Control Volume Switch Control JackModel H8068 wiring diagram H8068 Telecaster Style Kit Wiring DiagramWarranty and Returns Page Page