Grizzly H8068 owner manual Supplies/Tools, Recommended Tools & Supplies

Page 7

Supplies/Tools

The majority of the wooden components in this kit are fully machined from the factory and are ready for assembly. A small amount of sanding and fin- ishing is required to complete your guitar.

Recommended Tools & Supplies:

•Sharp Pencil

•Drill Press

•Drill Bits: 1⁄16", 7⁄64", 1⁄8", 5⁄16", 1⁄4"

•Electric/Cordless Drill

•Depth Stop

•NIOSH Approved Respirator

•ANSI Approved Safety Glasses

•Aluminum-Oxide Sanding Paper #150, #220 and #320 Grit

•Wet and Dry Sanding Paper #400, #600, and #1000 Grit

•Flexible Sanding Block

•Wood Glue

•Chisel or Razor Blade

•Phillips Head Screwdriver #1, #2

•1⁄4" Steel Rod or a Coat Hanger

•Masking Tape

H8068 Telecaster® Style Kit

•Tack Cloth or Clean Soft Rag

•Sanding Sealer

•Assorted Wood Files

•Buffing Compounds

•Oil Wood Finish

•Soldering Iron and Solder

•Peghead Reamer or a Round File

•Rubber Dead Blow Hammer

•Tweezers, Pliers, Wire Cutters

•C-Clamps

•Temporary Wood Handle: Approximately 1" x 2" x 16"

•Guitar Capo

•Feeler Gauge Set

•Spray Primer and Finish (See Note below)

•Spray Gun and Compressor

•18" Metal Straightedge (1⁄32" Resolution)

•36" Metal Straightedge

•Steel Ruler (1⁄64" Resolution)

•Wood Dowel

•Wooden Blocks: Approximately 4" x 4" x 12"

(2)

•Wood Shim 7⁄16" Thick

Note: Use the same type of paint for primer and finish—either enamel or lacquer base. Do not use different base paints for priming or finishing or your results may not be desir- able.

-5-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model H8068 Telecaster Style KIT Page Table of Contents Safety Foreword IntroductionContact Info Inventory Parts InventoryRecommended Tools & Supplies Supplies/ToolsIdentification Model H8068 headstock features H8068 Telecaster Style KitComponents and Hardware Needed Qty AssemblySanding Body Sanding NeckTo finish the guitar neck Finishing NeckTo finish the guitar body Finishing BodyTo mount the neck to the guitar body Mounting NeckTo determine neck mounting hole depth To drill mounting holes in the neck Another way to determine neck mounting hole depth OptionalTo mount the neck to the body To position the pick guard, control plate and bridge Positioning Pick Guard, Control Plate BridgeInto the control plate cavity Body, go to Installing Ferrules,To install the ferrules Installing FerrulesGo to Mounting Tuners on Mounting Tuners To install the tunersTo wire the pickups Wiring PickupsTo position the ground wire under the bridge Installing Output JackInstalling Bridge Control Plate To install the output jackTo attach the strap buttons to the guitar Installing NutTo install the nut Strap ButtonsWinding Strings To install strings through the bodyTo install the string retainer To install the strings using only the bridgeString Retainers General SetupNeck Adjustment To adjust the bow of the guitar neckString Height To adjust the string heightTools Needed Qty To measure the string height at the pickup Pickup Height TuningTo tune the guitar To set the intonation Setting IntonationReference Info AccessoriesModel H6976 H6976-The Fender TelecasterTo Bridge Electrical ComponentsPickup Ground Tone Control Volume Switch Control JackModel H8068 wiring diagram H8068 Telecaster Style Kit Wiring DiagramWarranty and Returns Page Page
Top Page Image Contents