Pioneer CDJ-1000 Disc LOADING/UNLOADING, DJ Player Operation, Auto Cueing, Starting Playback

Page 11

BASIC OPERATION

DISC LOADING/UNLOADING

Label surface up

Insert straight

1. Set the rear-panel POWER switch to ON.

Do not force a disc into the unit when the POWER switch is set to OFF as this may damage the disc and the unit.

2.Insert a disc.

Hold the disc with label surface upwards, and insert into the front panel disc loading slot .

When playing 8cm discs, be sure to install an adaptor.

This unit spins at high speed to provide high performance. When playing 8cm discs with an adaptor, for safety reasons the rotation speed is reduced as a result scratch and reverse speeds will be lower.

DJ PLAYER OPERATION

WAVE SEARCH(ZOOM)EJECT UNLOCK/LOCK

TIME MODE

2, 3

/ AUTO CUE

 

 

EJECT

0

TRACK

SEARCH

4, ¢

SEARCH

1, ¡

CUE

PLAY/PAUSE

6

Jog dial

Auto Cueing (*)

Auto cueing is used to automatically specify the Cue point (see p. 12) to be used before sound actually begins to play when inserting a disc or when performing track searching.

Turning auto cueing on and off

Pressing the TIME MODE/AUTO CUE button and holding it down for a second or more causes auto cueing to be alternately turned on and off.

When AUTO CUE is on, the [A. CUE] indicator will be lit up.

Only one disc can be loaded at a time. Never attempt to load more than one disc at the same time, or attempt to load a second disc when one disc has already been loaded.

When loading a disc, do not placing any twisting force on the disc, or try to force the disc into the slot. Also, do not attempt to interrupt or defeat the motion of the disc when the player begins to draw a disc into the slot or to eject a disc, since damage to the disc or player could occur.

3.The disc can be ejected anytime using the EJECT button (0) when the EJECT UNLOCK/LOCK switch is set to UNLOCK. When the EJECT UNLOCK/LOCK switch is set to LOCK, press the PLAY/PAUSE button (6) during playback, or when a Cue point has been set, press the CUE button (back cue) before pressing the EJECT button (0) to eject the disc.

When the EJECT button is pressed, disc rotation stops and the disc is ejected from the loading slot.

If the disc cannot be ejected with the EJECT button, insert a pin in the forced ejection hole on the front panel of the player. ☞ P. 5

CAUTION:

Do not attempt to press a disc back into the slot when the [EJECT] indicator appears. Pressing a disc back into the slot while the [EJECT] indicator appears may cause the player to stop. In this case, press the EJECT button again and wait until the [EJECT] indicator goes out be- fore reinserting the disc.

Buttons indicated by * cannot be used when the Digital Mode switch is set to on (and the digital output terminal is used).

AUTO CUE on/off status is stored in memory and persists even when the power is turned off.

It can change the Auto Cue level.

7Changing the Auto Cue level

1.Press the TIME MODE/AUTO CUE button for over 5 seconds.

The display will indicate [A.CUE-60dB](in the original state).

2.By -pressing the WAVE SEARCH (ZOOM) button (2, 3) you can change the level.

It can choose from -36dB, -42dB, -48dB, -54dB, -60dB, -66dB, -72dB and -78dB.

The level change mode can be removed if you press the TIME MODE/ AUTO CUE button or wait 15 seconds.

Even if you turn the power off, the set level will remain in memory.

Starting Playback

1.Insert a disc in the player.

This unit spins discs at high speeds to provide high performance. As a result, disc loading takes a couple of seconds.

2.If auto cueing is on, press the PLAY/PAUSE button (3/8).

Wait for the CUE button indicator to light up before pressing the button. The silent portion at the beginning of the displayed track will be skipped

and playback will begin instantaneously from the first bars of the track. Once the first track has been played, the player will automatically search for the beginning of the next track to be played. The cueing indicator [CUE] will light up, the PLAY/PAUSE button [3/8] indicator will flash, and the player will then wait for the PLAY/PAUSE button (3/8) to be pressed before begin- ning playback of the next track.

11

<DRB1297>

En

Page 10 Page 12
Image 11
Page 10 Page 12
Contents CDJ-1000 DRB1297 Important Notice Contents Do not play a CD with a special shape Cleaning and handling compact discsStoring discs CondensationChanges music tempo without changing pitch FeaturesResets the tempo to 0% regardless of slider position Allows you to replay a loop any number of timesConnections Connecting control cord to allow relay playConnecting to a stereo amplifier when not using a DJ mixer Connecting to other devicesConnecting the power cord Connecting to other mixersTop Panel Panel FacilitiesJog Dial Display DisplayStarting Playback Disc LOADING/UNLOADINGDJ Player Operation Auto CueingTrack Cueing Cue Point SettingsStopping Playback To Pause PlayMixing Different Tracks Changing Playback SpeedApplying Master Tempo Jog Dial FunctionsAdvanced Operations Wave Display Relay Play Using Two PlayersReversing Playback Fader Start PlaybackUsing a Commercially Available Multimedia Card Using CUE POINTS/LOOP Points MemoryUsing Internal Memory Copying MMC Data From One MMC to Another Symptom Cause Remedy TroubleshootingMalfunction of the MMC is not covered by warranty Specified time interval Way into disc insertion slot Error message displayCleaning the Jog Dial =Recommended action clean discAudio section SpecificationsAccessories General

CDJ-1000 specifications

The Pioneer CDJ-1000, introduced in the early 2000s, became an iconic digital turntable that transformed the world of DJing. Its blend of advanced technology and user-friendly design made it a preferred choice for both amateur and professional DJs.

One of the CDJ-1000's standout features is its large, pressure-sensitive jog wheel, which allows for precise control over track playback. This innovative design enables DJs to scratch, pitch-bend, and manipulate tracks intuitively, imitating the feel of traditional vinyl turntables. The jog wheel is surrounded by an LED display that provides real-time feedback on track position, pitch adjustments, and BPM, ensuring that DJs stay aligned with the music.

Another significant feature is the CDJ-1000's playback capability. It supports various audio formats, including standard CDs, CD-Rs, and MP3 files. This versatility allows DJs to curate performances using a broad array of music, making the device suitable for various events, from club gigs to festivals.

The CDJ-1000 also boasts a built-in memory function, enabling users to store cue points and loops, facilitating seamless transitions between tracks. DJs can easily navigate through their playlists, saving valuable time during performances. Additionally, the unit utilizes a digital audio output to maintain signal quality, ensuring the best possible sound reproduction.

The unit's compatibility with other Pioneer equipment, such as mixers, means that it can easily integrate into existing setups. This connectivity is enhanced through its digital link feature, which allows multiple CDJ-1000 units to be connected for synchronized play, creating a cohesive performance environment.

In terms of build quality, the CDJ-1000 is robust and designed to endure the rigors of live performance. Its layout is intuitive, with a user-friendly interface that enables quick access to essential functions.

Overall, the Pioneer CDJ-1000 redefined DJing by integrating digital technology without sacrificing the tactile experience of vinyl. Its combination of innovative features, support for multiple music formats, and reliable build quality cemented its status as a staple in the DJ industry, influencing future designs and technologies in the realm of digital DJing. It remains a beloved piece of equipment among many DJs today, reflecting its lasting impact on the art of mixing and performance.
Top Page Image Contents