Roland owner manual Troubleshooting, When the F-50 is connected to an external device

Page 27

Troubleshooting

	Case	Cause/Remedy


	The pedals are	Are the pedals connected properly?
	not functioning	(p. 11)

		Unplugging a pedal cord from the unit
	The pedals	while the power is on may cause the
	The pedals	pedal’s effect to be applied without
	function	pedal’s effect to be applied without
	function	stopping. The power of the F-50 must be
	intermittently	stopping. The power of the F-50 must be
	intermittently	turned off before inserting or removing
		turned off before inserting or removing
		a pedal cord (p. 11).

		Reverb is switched on automatically
	[Reverb]	whenever a demo song is played.
	button’s	Since each song has been supplied with
	indicator lights	its own reverb settings, the way in
	automatically	which reverb is applied changes when
		you switch demo songs.

When the F-50 is connected to an external device

		Is the power to all equipment turned
		on?

		Are the connections between F-50 and
	No sound is	the MIDI sequencer or the other
	No sound is	external devices correct? (p. 22, p. 23)
	produced	external devices correct? (p. 22, p. 23)

		Is the MIDI channel setting correct? (p.
		Is the MIDI channel setting correct? (p.
		25)

		Is the Omni On/Off setting correct? (p.
		24)

	Strange
	sounds (or two	With the sequencer’s “Thru” function
	sounds) are	With the sequencer’s “Thru” function
	sounds) are	on, the same notes may be sounded
	produced when	on, the same notes may be sounded
	produced when	twice. Set the F-50 to Local off (p. 24).
	the	twice. Set the F-50 to Local off (p. 24).
	the
	F-50 is played

	The volume
	level of the	Could you be using a connection cable
	instrument	that contains a resistor?
	connected to	Use a connection cable that does not
	the Input jack is	contain a resistor.
	too low

27

Image 27

Contents Page For the U.K Page Additional Precautions Power SupplyMaintenance PlacementMain Features IntroductionChecking the Included Items Introduction Assembly ProcedureAssembling the F-50 Check the PartsStand the instrument back up When Moving the InstrumentWhen Disassembling If the Stand is UnevenTone Tone Buttons Panel DescriptionsContents Connecting the AC Adaptor Installing the Music StandBefore You Play Connecting Pedals Turning On the PowerTurning Off the Power Min Max Adjusting the VolumeConnecting Headphones Use the Volume knob to adjust the overall volume levelSelecting a Song for Playback Listening to the Demo SongsListening to the Demo Songs Using Each Tone Listening to the Demo SongsPress Included in left-hand areas Playing the KeyboardPlaying the Keyboard Layering Two Instrument Sounds Dual PlayAdding Reverberation to Sounds Reverb Effect Recording a Performance Recording Your PerformanceDisabling Buttons Panel Lock Adjust the volumeSome Handy Functions Changing the Keyboard’s TouchAdjusting the Pitch of the Sound Master Tuning Lowering/ raising the Reference PitchSome Handy Functions Changing the Depth of the Reverb Effect Changing the Volume Balance in Dual PlaySetting the Reference Pitch to 440.0 Hz Setting the Reference Pitch to 442.0 HzMaking the Connections Connecting to Audio EquipmentRecording procedure About the JacksMidi Out Connector Connecting to Midi DevicesAbout the Midi Connectors Midi In ConnectorReceiving on all Midi channels Omni On/Off Switching Local On/OffSwitching Omni On/Off Connecting to Midi DevicesOff Set the Midi ChannelTransmitting a performance You recorded Midi ChannelCase Cause/Remedy TroubleshootingWhen the F-50 is connected to an external device TroubleshootingKey Song Name Composer Copyright Demo Song ListEb3 Demo Song ListAux Message123-127 Roland Digital Piano Main SpecificationsFunctions Assigned to the Keyboard Numerics IndexAfrica InformationAvis 03345901 ’05-2-3N