Behringer V-TONE GM110 user manual Control Elements, Front panel, Rear panel

Page 6

V-TONE GM110

2.CONTROL ELEMENTS

2.1Front panel

Fig. 2.1: Front panel control elements

INPUT is the GM110’s 1/4" jack input for your guitar. Use a

 

 

The SPEAKER switch provides you with simulations of

 

 

commercial 1/4" jack mono cable (not from a DIY shop, but

 

 

two classic guitar loudspeakers: 4x12"-loudspeakers in a

from a specialist music dealer).

 

 

closed back enclosure (U.K.), and 2x12" loudspeakers,

The DRIVE control determines the amplification in the input

 

 

open back (U.S.). In addition, we have also installed a

 

 

further frequency response correction (FLAT) that is

section. It allows you to finely tune the GM110 preset to the

 

 

 

 

specially adapted to the GM110 enclosure.

output level of your guitar pick-up (depending on selected

 

 

 

 

 

amp, mode and speaker combination) in order to achieve

 

 

The LOW control in the EQ section enables you to boost or

 

 

the desired degree of distortion.

 

 

cut the bass frequencies.

Use the DRIVE control to set the desired sound and

 

 

With the MID control, you can boost/cut the midrange

 

 

use the MASTER control to set the desired volume!

 

 

frequencies.

The AMP switch enables you to emulate the basic sounds

 

 

The HIGH control governs the upper frequency range.

 

 

from three guitar amp designs; these are based on classic

 

 

With the MASTER control, you determine the overall and

amp models and will be familiar to you from numerous

 

 

 

 

headphone volume of your V-TONE GM110. It should be

recordings. The TWEED setting delivers transparent

 

 

 

 

set fully to the left when you operate the POWER switch or

sounds, clear as a bell, with dynamic bass response. The

 

 

 

 

disconnect the instrument cable from the guitar or amp.

BRITISH setting has an aggression that comes straight from

 

 

 

 

 

the heart and is powerful with an unmistakable ability to

 

 

Use the POWER switch to put the GM110 into operation.

 

 

make itself heard. Fuller and more balanced, and yet subtly

 

 

The POWER switch should always be in the “Off” position

differentiated, the CALIF(ORNIAN) setting is particularly

 

 

when you are about to connect your unit to the mains.

suitable for singing lead sounds.

 

 

Attention: The POWER switch does not fully

With the MODE switch, you choose between one of three

 

 

 

 

disconnect the unit from the mains. Unplug the

possible gain settings (CLEAN, HI GAIN and HOT) to achieve

 

 

power cord completely when the unit is not used

the basic sound selected with the AMP switch.

 

 

for prolonged periods of time.

 

 

 

 

2.2 Rear panel

Fig. 2.2: Rear panel connectors

FUSEHOLDER / VOLTAGE SELECTION. Before you connect the device to the network, please make sure that your local voltage matches the voltage indicated on the unit. Blown fuses may only be replaced by fuses of the same type and rating. Some models allow for inserting the fuse holder in two different positions in order to switch over from 230 V to 120 V operation, and vice versa. Please note that, for 120 V operation outside Europe, you need to use a fuse of a higher rating. The network connection is made via a STANDARD IEC INLET SOCKET. Use the enclosed power cord to connect the unit to the mains.

6

2. CONTROL ELEMENTS

Image 6
Contents Tone Important Safety Precautions Detailed Safety InstructionsTone Table of Contents ForewordIntroduction Design concept Dynamizer technology and analog modelingBefore you get started Control Elements Front panelRear panel Wiring Tips Serial NumberSpecifications Loudspeaker connectionWarranty