VTX350H
TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4,5 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 The DSP Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Storing Your Own Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Restoring the Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 More About The Save/Tap Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Using the Footswitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 DSP Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10,11 Suggested Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12,13 DSP “Fill in the Blanks” (for User Presets) . . . . . . . . . . . . . . . . . . . . .14 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequen- cy energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a par- ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device not expressly approved by SLM Electronics could void the user’s authority to operate the equipment under FCC rules.
| Declaration of Conformity |
Manufacturer’s Name: | SLM Electronics |
Corporate Headquarters: | 1901 Congressional Drive, St. Louis, Missouri 63146 |
Primary Production Facility: | 700 Hwy 202 W, Yellville, Arkansas, 72687 |
Product Type: | Audio Amplifier |
Products meet the regulations for compliance marking under: ETL standards UL6500, UL60065, or UL813 CSA standards E60065 or C22.2
CE EMC standards EN55103 or EN55013 and EN61000
Compliance Support Contact: SLM Electronics, Attn: R&D Compliance Engineer
1901 Congressional Drive, St Louis, Missouri, 63146 • Tel.: