Pioneer VSX-AX4AVi-G, VSX-AX2AV-G Other connections Connecting a PC for Advanced Mcacc output

Page 59

Other connections

08

Connecting a PC for Advanced MCACC output

If you use the Professional Acoustic Calibration EQ (see page 38) to measure the reverb characteristics of your listening room, you can check the results graphically using a computer connected to this receiver. Use a commercially-available RS-232C cable to connect the RS- 232C jack on your computer to the 9-pin RS-232C jack on the back panel of this receiver (the cable must be cross type, female–female).

To obtain the software to output the results, please register this unit online as instructed on the front cover of the manual. After registering, you will receive an email within a week, in which both the software and instruction manual will be available. If you have any questions regarding, please contact the Customer Support Division of Pioneer.

Please make sure your system meets the following requirements:

•Operating system must be Windows® XP, Windows® 2000, Windows® Millennium Edition, Windows® 98 Second Edition, or Windows® NT 4.0 (Service pack 6).

•CPU must be at least Pentium 3 / 300MHz or AMD K6 / 300MHz (or equivalent) with at least 128MB of memory, and your monitor must be able to display a minimum resolution of 800x600.

•An RS-232C port connector is necessary for graphical output. Refer to the operating instructions and/or the PC manufacturer for more information on making the proper port settings.

•System must have internet access.

•Connect your computer to the RS-232C jack on the rear panel of the receiver.

Make sure that the receiver and all connected components are switched off and disconnected from the power outlet when you do this.1

Use a commercially-available cable to connect the RS- 232C jack on your computer to the 9-pin RS-232C jack on this receiver. See the documentation provided with the Advanced MCACC application for more information.

RS-232C

PC

Advanced MCACC output using your PC

Before continuing, make sure you have completed steps 1–3 in Professional Acoustic Calibration EQ on page 38. Note that transmission data is erased when the receiver is turned off.

1Select ‘Reverb Output PC’ and press ENTER. When the receiver is ready for transmission, Start the MCACC application on your PC shows on the OSD.

3e.EQ Professional

 

3e3.Reverb Output PC

 

1.Reverb

Measurement

 

MCACC:M1. MEMORY 1

 

2.Reverb

View

 

 

 

 

3.Reverb

Output

PC

 

 

Start the MCACC

 

4.Advanced EQ

Setup

 

 

 

 

 

 

 

 

application on your PC

ENTER:Next

:Return

 

:Cancel

2Start the MCACC application on your computer. Follow the instructions provided with the application. It will take about ten seconds for the transmission to complete, then you will be able to analyze the output on your computer. Since the data will be cleared from the receiver when you restart reverb measurement or turn off the receiver, you might want to save the information on your PC after measurement.

3When you’re finished, press RETURN.

You’ll be taken to the Advanced EQ Setup. Depending on the results, you may want to continue with the Advanced EQ setup (see Using Professional Acoustic Calibration EQ on page 40 for more on this). You can also simply press RETURN again to exit the Professional Acoustic Calibration EQ setup.

Note

1Make sure that you do this before continuing to the Reverb Measurement option in Using Professional Acoustic Calibration EQ on page 40 (measure- ment data is cleared if you switch off the power).

59

En

Page 58 Page 60
Image 59
Page 58 Page 60
Contents VSX-AX4AVi-GVSX-AX2AV-G Risk of Electric Shock Do not Open Operating EnvironmentFor Taiwan exclusively Changing the TV format settingDisplay shows the new setting PAL or Ntsc Voltage selectorContents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box Installing the receiverBefore you start Before you start ChapterIntroduction to home theater Automatically setting up for surround sound McaccMinute guide Minute guide ChapterEnter 02 5 minute guidePlaying a source Better sound using Phase ControlProblems when using the Auto Mcacc Setup Minute guideRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections 324 Connecting your equipment Connecting your TV and DVD playerUse an optical cable for the connection Or other set-top box Other video sourcesDVD player Using the component video jacksFor a second recorder, use the DVR/VCR2 outputs Use a three-way component video cableAbout the WMA9 Pro decoder Connecting your equipment Connecting digital audio sourcesInput Selector dial front panel to select Connecting your equipment Connecting analog audio sourcesConnecting a component to the front panel inputs Select these inputs using Input Select remote orConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsAssemble the stand as shown in the illustration Connecting antennasTHX speaker system setup AM loop antennaAntenna FM wire antennaUsing an external antenna to improve FM reception Using an external antenna to improve AM receptionAC power cord and converter plug use Connecting your equipment Plugging in the receiverSTANDBY/ON Controls and displaysControls and displays Chapter Front panelControls and displays Operating range of remote control unitControls and displays Display 6TUNE/ST /ENTER Controls and displays Remote controlReceiver Input SelectSource StatusMultiope ShiftListening in surround sound Listening to your systemListening to your system Chapter Auto playbackListening to your system Using the Home THX modesUsing the Advanced surround effects THX Games ModeListening to your system Listening in stereo Using Stream DirectSelecting Mcacc presets Choosing the input signalUsing the Virtual Surround Back mode Using surround back channel processingListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsAutomatic Mcacc Expert System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuMemory System Setup menuIf necessary, confirm the speaker configuration in the OSD.1 Surround back speaker settingFine Channel Level Manual Mcacc setupStanding Wave Adjust the level of the left channelWhen youre finished, press Return Fine Speaker DistanceAcoustic Calibration EQ Select ‘Standing Wave’ from the Manual Mcacc setup menuSelect ‘EQ Adjust’ from the Manual Mcacc setup menu Select the channels you want and adjust to your likingHow to interpret the graphical output How to use Professional Acoustic Calibration EQSelect an option and press Enter Using Professional Acoustic Calibration EQSelect ‘EQ Professional’ then press Enter Data Management Checking Mcacc preset dataCopying Mcacc preset data Clearing Mcacc presets Manual speaker setupSpeaker Setting Renaming Mcacc presetsConfirm your selected setup option Select ‘Speaker Setting’ from the Manual SP Setup menuSelect ‘Channel Level’ from the Manual SP Setup menu Select a setup optionEnter Speaker DistanceBass Peak Level Curve THX Audio SettingOther connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsButton What it does Connecting using HdmiOther connections Basic playback controlsOn a HDMI-compatible monitor.1 Using the i.LINK interfaceAbout Hdmi Checking the i.LINK inputs About i.LINKCreating an i.LINK network About Pqls rate controlUse standard RCA/phono jack cables for the connections Using the USB interfaceConnecting the multichannel analog inputs Selecting the multichannel analog inputsStart playback of a source on your computer Second Zone speaker B setupSwitching the speaker system Use the Input Select button to select USBConnect your speakers as shown below Bi-wiring your speakersBi-amping your front speakers Making multi-room connections Other connections Connecting additional amplifiersMulti-room listening Sub room Input sources available Basic multi-room setup RoomMulti-room listening options Input Connecting an IR receiverUsing the multi-room controls Multi-room remote controlsPioneer plasma display Using this receiver with a Pioneer plasma displaySwitching components on and off using the 12 volt trigger DVD player Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma DisplayAdvanced Mcacc output using your PC Other connections Connecting a PC for Advanced Mcacc outputInput Setup menu Other SettingsOther Settings Chapter Select ‘Other Setup’ then press Enter Other SettingsOther Setup menu Input function default and possible settingsSR+ Setup for Pioneer plasma displays Multi-Room and IR receiver setupOSD Adjustment Setting What it does Options Using other functionsUsing other functions Chapter Setting the AV optionsRecout Source Using other functionsPlaying a different source when recording Making an audio or a video recordingDimming the display Switching the speaker impedanceUsing the sleep timer Checking your system settingsSetting Default Resetting the systemDefault system settings Display shows RESET?Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesDirect function Multi Operation and System OffUsing System off Using multi operationsFunction Components Controlling the rest of your system Controls for TVsControls for other components Buttons Function ComponentsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorButton s Function Components Additional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsProfessional Calibration EQ graphical output DisplayLink interface Remote controlMessage Explanation Link messagesUSB interface Jacks Symptom Cause ActionThere is a problem with the signal path from IPod messagesWindows Media Audio 9 Professional Additional information Surround sound formatsDolby About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Surround Multichannel signal formatsInput signal format Standard Unavailable with only one surround back speaker connected Input signal formatSurround Back speakers Additional information Specifications Additional information Our philosophy Cleaning the unitFeatures 05F00001 Printed ARB7336-A Pioneer Corporation

VSX-AX4AVi-G, VSX-AX2AV-G specifications

The Pioneer VSX-AX4AVi-G and VSX-AX2AV-G are two impressive receivers that exemplify Pioneer’s commitment to high-fidelity audio performance and advanced home theater technology. Both models cater to audio enthusiasts and casual listeners alike with their robust feature sets and innovative technologies.

The VSX-AX4AVi-G is a flagship model that boasts a powerful 7.1 channel surround sound system, delivering an immersive audio experience. With 130 watts per channel, it ensures that even the most demanding soundtracks are reproduced with clarity and strength. Supporting various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, the receiver creates a cinema-like experience at home. The inclusion of Pioneer's proprietary MCACC (Multi-Channel Acoustic Calibration System) enables automatic speaker setup and calibration, optimizing audio quality based on the specific characteristics of the room.

In contrast, the VSX-AX2AV-G is designed for those seeking high-end audio without a plethora of features. While it also supports 7.1 channel playback, it focuses on delivering a more straightforward user experience. The AX2AV-G offers similar power output per channel, ensuring rich and full-bodied sound reproduction. Its straightforward user interface makes it accessible for users who want quality audio without the complexity.

Both models feature advanced video processing capabilities and support high-definition video formats. They can upscale standard-definition content to 1080p through HDMI, ensuring that users get the best quality possible from their video sources. The HDMI connectivity allows for multiple input sources and supports 4K video resolution, making both receivers future-proof for evolving home theater setups.

In terms of connectivity, the VSX-AX4AVi-G and VSX-AX2AV-G offer a wide range of inputs and outputs, including multiple HDMI ports, component video inputs, and composite connections, accommodating various devices such as Blu-ray players, gaming consoles, and streaming devices. The receivers also feature advanced digital signal processing, enhancing sound quality and making music playback more enjoyable.

Additionally, these receivers come equipped with a range of audio enhancement features such as Phase Control and Advanced Sound Retriever, which help to improve audio playback by enhancing high frequencies and restoring lost details, especially when streaming compressed audio formats.

In summary, the Pioneer VSX-AX4AVi-G and VSX-AX2AV-G represent two excellent options in the receiver market. With their combined focus on high-quality audio, advanced video processing, and user-friendly operation, they provide an ideal solution for anyone looking to enhance their home entertainment experience.
Top Page Image Contents