Pioneer VSX-AX2AV-G, VSX-AX4AVi-G manual Display, Professional Calibration EQ graphical output

Page 76

12Additional information

Symptom

Remedy

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

Setup, the speaker size setting is

off all other appliances in the room and use Auto MCACC Setup again.

incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

 

Change the speaker setting manually in Speaker Setting on page 42, and use the ALL (Keep SPsetting)

 

option for the Auto Mode in Automatic MCACC (Expert) on page 33 if this is a recurring problem.

 

 

Can’t adjust the Fine Speaker

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

Distance setting (page 37)

matched up properly).

properly.

 

 

 

The display shows KEY LOCK

• With the receiver in standby, press STANDBY/ON while holding down the MULTI-ROOM&SOURCE

ON when you try to make

CONTROL button to disable the key lock.

settings.

 

 

 

Most recent settings have been

• The power cord was disconnected from the wall while adjusting this setting.

erased.

 

 

 

Professional Calibration EQ graphical output

Symptom

Remedy

The EQ response displayed in the

• There are cases where the graph does not appear flat (even when selecting ALL CH ADJUST in the Auto

graphical output following

MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.

calibration does not appear

• Areas of the graph may appear identical (before and after) when there is little or no adjustment needed.

entirely flat.

• The graph may appear to have shifted vertically when comparing before and after measurements.

 

 

EQ adjustments made using the

• Despite level adjustments being made, the filters used for analysis may not display these adjustments in

Manual MCACC setup on

the graphical output. However, these adjustments are taken this into account by the filters dedicated to

page 36 do not appear to change

overall system calibration.

the graphical output.

 

 

 

Lower frequency response

• Low frequencies used in bass management (the subwoofer channel) will not change for speakers that

curves do not seem to have been

have been specified as SMALL in the configuration, or do not output these frequencies.

calibrated for SMALL speakers.

• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable sound is

 

output for display.

 

 

Graphical output data seems to

• If the power is switched off, the measurement data for graphical output to a PC is cleared.

have disappeared.

 

 

 

Display

Symptom

Remedy

The display is dark or off.

• Press DIMMER on the remote control repeatedly to select a different brightness.

 

 

After making an adjustment the

• Press DIMMER on the remote control repeatedly to select a different brightness.

display goes off.

 

 

 

You can't get DIGITAL to display

• Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input

when using the SIGNAL SELECT

Setup menu on page 60).

button.

• If the multichannel analog inputs are selected, select a different input source.

 

 

The Dolby/DTS indicator doesn't

• These indicators do dot light if playback is paused.

light when playing Dolby/DTS

• Check the playback (especially the digital output) settings of the source component.

software.

 

 

 

When playing a DVD-Audio disc,

• This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of

the DVD player display shows

the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.

96 kHz. However, the receiver’s

 

display does not.

 

 

 

During playback of a DTS 96/24

• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 29).

source, the display doesn't show

 

96kHz.

 

 

 

76

En

Page 75 Page 77
Image 76
Page 75 Page 77
Contents VSX-AX4AVi-GVSX-AX2AV-G Operating Environment Risk of Electric Shock Do not OpenChanging the TV format setting Display shows the new setting PAL or NtscVoltage selector For Taiwan exclusivelyContents Other Settings Using other functionsOther connections Controlling the rest of your systemInstalling the receiver Before you startBefore you start Chapter Checking what’s in the boxAutomatically setting up for surround sound Mcacc Minute guideMinute guide Chapter Introduction to home theater02 5 minute guide EnterBetter sound using Phase Control Problems when using the Auto Mcacc SetupMinute guide Playing a sourceConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter Connecting your equipment Connecting your TV and DVD player 324Or other set-top box Other video sources Use an optical cable for the connectionUsing the component video jacks For a second recorder, use the DVR/VCR2 outputsUse a three-way component video cable DVD playerConnecting your equipment Connecting digital audio sources About the WMA9 Pro decoderConnecting your equipment Connecting analog audio sources Connecting a component to the front panel inputsSelect these inputs using Input Select remote or Input Selector dial front panel to selectConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupAM loop antenna Assemble the stand as shown in the illustrationFM wire antenna Using an external antenna to improve FM receptionUsing an external antenna to improve AM reception AntennaConnecting your equipment Plugging in the receiver AC power cord and converter plug useControls and displays Controls and displays ChapterFront panel STANDBY/ONOperating range of remote control unit Controls and displaysControls and displays Display Controls and displays Remote control ReceiverInput Select 6TUNE/ST /ENTERStatus MultiopeShift SourceListening to your system Listening to your system ChapterAuto playback Listening in surround soundUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Stream Direct Selecting Mcacc presetsChoosing the input signal Listening to your system Listening in stereoUsing surround back channel processing Using the Virtual Surround Back modeUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Automatic Mcacc ExpertSystem Setup menu MemorySurround back speaker setting If necessary, confirm the speaker configuration in the OSD.1Manual Mcacc setup Fine Channel LevelAdjust the level of the left channel When youre finished, press ReturnFine Speaker Distance Standing WaveSelect ‘Standing Wave’ from the Manual Mcacc setup menu Select ‘EQ Adjust’ from the Manual Mcacc setup menuSelect the channels you want and adjust to your liking Acoustic Calibration EQHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputSelect ‘EQ Professional’ then press Enter Using Professional Acoustic Calibration EQSelect an option and press Enter Copying Mcacc preset data Checking Mcacc preset dataData Management Manual speaker setup Speaker SettingRenaming Mcacc presets Clearing Mcacc presetsSelect ‘Speaker Setting’ from the Manual SP Setup menu Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Confirm your selected setup optionBass Peak Level Speaker DistanceEnter THX Audio Setting CurveConnecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterConnecting using Hdmi Other connectionsBasic playback controls Button What it doesAbout Hdmi Using the i.LINK interfaceOn a HDMI-compatible monitor.1 About i.LINK Checking the i.LINK inputsAbout Pqls rate control Creating an i.LINK networkUsing the USB interface Connecting the multichannel analog inputsSelecting the multichannel analog inputs Use standard RCA/phono jack cables for the connectionsSecond Zone speaker B setup Switching the speaker systemUse the Input Select button to select USB Start playback of a source on your computerBi-amping your front speakers Bi-wiring your speakersConnect your speakers as shown below Multi-room listening Other connections Connecting additional amplifiersMaking multi-room connections Multi-room listening options Basic multi-room setup RoomSub room Input sources available Connecting an IR receiver Using the multi-room controlsMulti-room remote controls InputSwitching components on and off using the 12 volt trigger Using this receiver with a Pioneer plasma displayPioneer plasma display Using the SR+ mode with a Pioneer plasma display Pioneer plasmaDisplay DVD player Satellite receiver, etcOther connections Connecting a PC for Advanced Mcacc output Advanced Mcacc output using your PCOther Settings Chapter Other SettingsInput Setup menu Other Settings Other Setup menuInput function default and possible settings Select ‘Other Setup’ then press EnterOSD Adjustment Multi-Room and IR receiver setupSR+ Setup for Pioneer plasma displays Using other functions Using other functions ChapterSetting the AV options Setting What it does OptionsUsing other functions Playing a different source when recordingMaking an audio or a video recording Recout SourceSwitching the speaker impedance Using the sleep timerChecking your system settings Dimming the displayResetting the system Default system settingsDisplay shows RESET? Setting DefaultSetting the remote to control other components Selecting preset codes directlyProgramming signals from other remote controls Controlling the rest of your systemErasing one of the remote control button settings Resetting the remote control presetsConfirming preset codes Controlling the rest of your systemRenaming input source names Direct functionMulti Operation and System Off Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offControlling the rest of your system Controls for TVs Controls for other componentsButtons Function Components Function ComponentsButton s Function Components Operating other Pioneer components with this unit’s sensorDecide which component you want to use the remote sensor Troubleshooting PowerAdditional information Additional information ChapterOther audio problems Additional informationSettings VideoDisplay Professional Calibration EQ graphical outputRemote control Link interfaceUSB interface Link messagesMessage Explanation Symptom Cause Action There is a problem with the signal path fromIPod messages JacksDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THX Listening modes with different input signal formats Stereo 2 channel signal formatsTHX Games Mode THX MusicModeInput signal format Standard Multichannel signal formatsAuto Surround Surround Back speakers Input signal formatUnavailable with only one surround back speaker connected Additional information Specifications Features Cleaning the unitAdditional information Our philosophy Pioneer Corporation 05F00001 Printed ARB7336-A

VSX-AX4AVi-G, VSX-AX2AV-G specifications

The Pioneer VSX-AX4AVi-G and VSX-AX2AV-G are two impressive receivers that exemplify Pioneer’s commitment to high-fidelity audio performance and advanced home theater technology. Both models cater to audio enthusiasts and casual listeners alike with their robust feature sets and innovative technologies.

The VSX-AX4AVi-G is a flagship model that boasts a powerful 7.1 channel surround sound system, delivering an immersive audio experience. With 130 watts per channel, it ensures that even the most demanding soundtracks are reproduced with clarity and strength. Supporting various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, the receiver creates a cinema-like experience at home. The inclusion of Pioneer's proprietary MCACC (Multi-Channel Acoustic Calibration System) enables automatic speaker setup and calibration, optimizing audio quality based on the specific characteristics of the room.

In contrast, the VSX-AX2AV-G is designed for those seeking high-end audio without a plethora of features. While it also supports 7.1 channel playback, it focuses on delivering a more straightforward user experience. The AX2AV-G offers similar power output per channel, ensuring rich and full-bodied sound reproduction. Its straightforward user interface makes it accessible for users who want quality audio without the complexity.

Both models feature advanced video processing capabilities and support high-definition video formats. They can upscale standard-definition content to 1080p through HDMI, ensuring that users get the best quality possible from their video sources. The HDMI connectivity allows for multiple input sources and supports 4K video resolution, making both receivers future-proof for evolving home theater setups.

In terms of connectivity, the VSX-AX4AVi-G and VSX-AX2AV-G offer a wide range of inputs and outputs, including multiple HDMI ports, component video inputs, and composite connections, accommodating various devices such as Blu-ray players, gaming consoles, and streaming devices. The receivers also feature advanced digital signal processing, enhancing sound quality and making music playback more enjoyable.

Additionally, these receivers come equipped with a range of audio enhancement features such as Phase Control and Advanced Sound Retriever, which help to improve audio playback by enhancing high frequencies and restoring lost details, especially when streaming compressed audio formats.

In summary, the Pioneer VSX-AX4AVi-G and VSX-AX2AV-G represent two excellent options in the receiver market. With their combined focus on high-quality audio, advanced video processing, and user-friendly operation, they provide an ideal solution for anyone looking to enhance their home entertainment experience.
Top Page Image Contents