Pioneer VSX-D511 Connecting up Connecting DVD 5.1 channel components, Connecting video components

Page 13

Connecting up

Connecting DVD 5.1 channel components

If you prefer to use a seperate component for decoding DVDs, you can connect a decoder or a DVD player with multi-channel analog outputs to the multi-channel inputs of this receiver.

When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from the wall outlet.

03

CENTER

OUTPUT

SUBWOOFER

OUTPUT

SURROUND OUTPUT DVD/multi-channel decoder

VIDEO

with 5.1 channel analog

output jacks

OUTPUT

 

FRONT

 

OUTPUT

 

The arrows indicate the direction of the signal.

The 5.1 channel input can only be used when DVD 5.1 CH is selected (see page 28).

Connecting video components

Connect your video components to the jacks as shown below. Regarding digital video components (like a DVD player), you must use the connections pictured on this page for the video signal, but in order to hear a digital source (like a DVD) you should hook up the audio to a digital input (see page 12). It is also a good idea to hook up your digital components with analog audio connections (see page 12).

For better quality video, you can hook up using the S-video jacks on the rear of the receiver instead of the regular video jacks (VSX-D511 only). Make sure you use an S-video cable to connect to the S- video jack on the component you are hooking up (see page 11).

When connecting your equipment always make sure the power is turned off and the power cord is disconnected from the wall outlet.

AUDIO

INPUT

VIDEO

INPUT

S-VIDEO

INPUT

S-VIDEO

OUTPUT

The arrows indicate the

VIDEO

Video deck

direction of

OUTPUT

AUDIO

OUTPUT

the signal.

13

En

Page 12 Page 14
Image 13
Page 12 Page 14
Contents VSX-D411VSX-D511 Important Notice Page Contents Operating range of remote control unit Installing the receiverBefore you start Checking what’s in the box Making cable connections02 5 minute guide Introduction to home theater Hook up your DVD player Minute guide Listening to Surround SoundHook up your TV Connect your speakers 02 5 minute guideMinute guide Play a DVD, and adjust the volume to your liking 1ch 0ch 02 5 minute guide Using the Quick Setup 1ch Press EnterAudio/Video cords Connecting upDigital audio cords/Optical cables Video cables VSX-D511 onlyConnecting audio components Connecting up Connecting digital componentsConnecting video components Connecting up Connecting DVD 5.1 channel componentsSignal Arrows indicateFM wire antenna Connecting antennasUsing external antennas Connecting up AM loop antennaAntenna snap connectors To improve FM receptionSpeaker terminals Connecting the speakersSnap shut the speaker terminal to secure Hints on speaker placement By connecting a control cord optional Connecting up AC outletOperating other Pioneer components Connected equipment should not exceed 100 W 0.8 a10 11 12 13 14 15 16 17 18 Controls and displays Front PanelControls and displays Master VolumeDisplay DTSATT PRO LogicDirect MidnightDVD Controls and displays Remote ControlReceiver Audio TOP MenuSubtitle Stereo/Direct Playing sources Introduction to Sound ModesStandard modes Advanced Surround modesUsing Stereo/Direct Choosing the input signalPlaying sources ExpandedUsing Loudness and Midnight listening Using Advanced SurroundPlaying sources Listening to multi-channel playback Pro Logic Music Pro Logic II MoviePlaying other sources Using the tone controlsMidnight Off Loudness TreblePlaying sources Selecting the multi-channel analog inputs Press Signal Select front panel repeatedly to select 5.1 chSelect DVD/LD if it is not already selected Choosing your receiver setup Setting up the receiverSpeaker setting Subwoofer settingSubwoofer setting Speaker settingCrossover frequency setting FL-C -SSFront speaker distance setting LFE attenuator settingCenter speaker distance setting Surround speaker distance set- tingDual mono setting Dynamic range control settingCoaxial digital input setting Optical digital input settingUse Level +/- to adjust the speaker levels in turn Setting the relative volume level of each channelWhen you’re done, press Test Tone to turn off the test tone Press Standard Press Test Tone to output the test toneImproving FM stereo sound Using the tuner Listening to the radioTune to a station you want to memo Rize Using the tuner Saving station presetsDisplay shows ST. MEMORY, then a blinking memory class Listening to station presets Using the tuner Naming station presetsChoose the station preset you want to name Press Station +/- to select the station preset you wantMonitoring your recording Making Recordings Making an audio or a video recordingAdjust the Master Volume Additional information TroubleshootingPlace the antenna farther away from the equipment causing ReceiverFront panel refer to Additional informationRemove the obstacle or operate from another position LightAmplifier Section Additional information SpecificationsVideo Section FM Tuner SectionDimensions Power Consumption 260 W16-9/16 W x 6-4/16 H x 15-8/16 D 19.8 lbAdditional information Additional information TNGZF/01L00001 Printed XRB3011-A 0 4 2 1 1 4 0
Top Page Image Contents