Pioneer VSX-D511, VSX-D41 manual LFE attenuator setting, Front speaker distance setting

Page 31

Setting up the receiver

100Hz 150Hz

200Hz

100 Hz

Sends bass frequencies below 100 Hz to the subwoofer (or L speakers).

150 Hz

Sends bass frequencies below 150 Hz to the subwoofer (or L speakers).

200 Hz

Sends bass frequencies below 200 Hz to the subwoofer (or L speakers).

If all speakers (front, center, and surround) are set to L, the crossover frequency can’t be set because there are no S speakers

( appears in the display).

LFE attenuator setting

•Default setting: 0 dB

Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers.

•Use ’ or ‘ to set the attenuation level (0 dB, 10 dB or dB(∞ )).

0 dB

 

10 dB

 

∞(displays )

When ∞ is selected ( appears in the display), LFE is not available.

06

Front speaker distance setting

•Default setting: 10 ft.

Sets the distance from the front speakers to the listening position.

•Use ’ or ‘ to set the distance of the front speakers from the main listening position (within a 30 foot range).

Center speaker distance setting

•Default setting: 10 ft.

The center speaker is normally placed directly in the front of the listening room and closer to the listening position than the front speakers. This means that the sound from the center speaker will be heard before the front speakers. To prevent this, set the center speaker distance setting to delay the sound from the center speaker so that the sound from the front and center speakers will be heard at the same time.

•Use ’ or ‘ to set the distance of the center speaker from the main listening position (within a 30 foot range).

When C is selected in the speaker setting, the center distance can’t be set.

Surround speaker distance set- ting

•Default setting: 10 ft.

Like the center speaker, you should set the distance of the surround speakers accurately to hear sounds coming from both front and surround speakers at the same time.

•Use ’ or ‘ to set the distance of the surround speakers from the main listening position (within a 30 foot range).

31

En

Page 30 Page 32
Image 31
Page 30 Page 32
Contents VSX-D411VSX-D511 Important Notice Page Contents Making cable connections Installing the receiverOperating range of remote control unit Before you start Checking what’s in the box02 5 minute guide Introduction to home theater Hook up your DVD player Minute guide Listening to Surround SoundHook up your TV Connect your speakers 02 5 minute guideMinute guide Play a DVD, and adjust the volume to your likingPress Enter 02 5 minute guide Using the Quick Setup1ch 0ch 1chVideo cables VSX-D511 only Connecting upAudio/Video cords Digital audio cords/Optical cablesConnecting audio components Connecting up Connecting digital componentsArrows indicate Connecting up Connecting DVD 5.1 channel componentsConnecting video components SignalFM wire antenna Connecting antennasTo improve FM reception Connecting up AM loop antennaUsing external antennas Antenna snap connectorsSpeaker terminals Connecting the speakersSnap shut the speaker terminal to secure Hints on speaker placement Connected equipment should not exceed 100 W 0.8 a Connecting up AC outletBy connecting a control cord optional Operating other Pioneer components10 11 12 13 14 15 16 17 18 Controls and displays Front PanelDTS Master VolumeControls and displays DisplayMidnight PRO LogicATT DirectDVD Controls and displays Remote ControlReceiver Audio TOP MenuSubtitle Advanced Surround modes Playing sources Introduction to Sound ModesStereo/Direct Standard modesExpanded Choosing the input signalUsing Stereo/Direct Playing sourcesPro Logic Music Pro Logic II Movie Using Advanced SurroundUsing Loudness and Midnight listening Playing sources Listening to multi-channel playbackTreble Using the tone controlsPlaying other sources Midnight Off LoudnessPlaying sources Selecting the multi-channel analog inputs Press Signal Select front panel repeatedly to select 5.1 chSelect DVD/LD if it is not already selected Subwoofer setting Setting up the receiverChoosing your receiver setup Speaker settingFL-C -SS Speaker settingSubwoofer setting Crossover frequency settingSurround speaker distance set- ting LFE attenuator settingFront speaker distance setting Center speaker distance settingOptical digital input setting Dynamic range control settingDual mono setting Coaxial digital input settingPress Standard Press Test Tone to output the test tone Setting the relative volume level of each channelUse Level +/- to adjust the speaker levels in turn When you’re done, press Test Tone to turn off the test toneImproving FM stereo sound Using the tuner Listening to the radioTune to a station you want to memo Rize Using the tuner Saving station presetsDisplay shows ST. MEMORY, then a blinking memory class Press Station +/- to select the station preset you want Using the tuner Naming station presetsListening to station presets Choose the station preset you want to nameMonitoring your recording Making Recordings Making an audio or a video recordingReceiver Additional information TroubleshootingAdjust the Master Volume Place the antenna farther away from the equipment causingLight Additional informationFront panel refer to Remove the obstacle or operate from another positionFM Tuner Section Additional information SpecificationsAmplifier Section Video Section19.8 lb Power Consumption 260 WDimensions 16-9/16 W x 6-4/16 H x 15-8/16 DAdditional information Additional information TNGZF/01L00001 Printed XRB3011-A 0 4 2 1 1 4 0

VSX-D511, VSX-D41 specifications

The Pioneer VSX-D41 and VSX-D511 represent a significant step forward in home audio technology for their time, offering robust features and advanced technologies that cater to home theater enthusiasts.

The VSX-D41 is a 5.1-channel receiver that delivers a power output of 100 watts per channel, prominent for providing a rich and immersive audio experience. The receiver supports various surround sound formats, including Dolby Digital and DTS, ensuring that users can enjoy precise audio reproduction for movies, music, and games. Its Audio Delay feature allows synchronization of sound with the on-screen action, enhancing the viewing experience. Additionally, the VSX-D41 includes a built-in equalizer for sound customization, enabling users to fine-tune their listening experience according to their preferences.

On the other hand, the VSX-D511 takes these features a step further with its 6.1 channel support. This model also boasts 100 watts per channel but adds an extra rear speaker channel for a more encompassing surround sound experience. The VSX-D511 comes equipped with Pioneer's Multi-Channel Acoustic Calibration System (MCACC), which analyzes the unique acoustics of a room to optimize speaker settings for balanced sound throughout. This ensures that users receive the best possible audio quality regardless of their room's layout.

Both models feature advanced connectivity options, including multiple audio inputs and outputs, allowing for seamless integration with various audio and video components. The inclusion of digital audio inputs provides flexibility in connecting modern devices. Additionally, the receivers feature a clear and user-friendly onscreen display, making navigation through settings and available inputs straightforward.

In terms of build quality, both receivers feature a robust design that is emblematic of Pioneer's commitment to durability and performance. They can handle high-definition audio signals, making them suitable for both legacy and contemporary audio sources.

In conclusion, the Pioneer VSX-D41 and VSX-D511 embody the advancements in audio technology during their era. With their powerful audio output, support for multiple surround sound formats, and user-friendly features, these AV receivers are excellent choices for enhancing any home theater system, delivering an unforgettable audio experience.
Top Page Image Contents