Pioneer VSX-03TXH manual Follow the instructions on-screen, Check

025 minute guide

Automatically setting up for surround sound (Auto MCACC)

•Push down on the PUSH OPEN tab to access the MCACC SETUP MIC jack:

AUTO SURR/	HOME	STANDARD	ADVANCED	STEREO/
STREAM DIRECT	THX	SURROUND	SURROUND	A.L.C.

PHONES

	VIDEO INPUT		iPod DIRECT	MCACC
VIDEO	L AUDIO R	DIGITAL IN	USB	SETUP MIC

MULTI-ZONE

The Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker size and distance, and tests for both channel delay and channel level. After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization for your particular room.

Make sure you do this before moving on to Playing a source on page 11.

Important

•Make sure the microphone and speakers are not moved during the Auto MCACC Setup.

•Using the Auto MCACC Setup will overwrite any existing settings for the MCACC preset you select.

•Before using the Auto MCACC Setup, the headphones should be disconnected and the iPod USB, XM or SIRIUS Radio function should not be selected as an input source.

Caution

•The test tones used in the Auto MCACC Setup are output at high volume.

				AUDIO		VIDEO	ANT	MPX SIGNAL SEL
				PARAMETER		PARAMETER
RECEIVER			SOURCE	EXIT	TUNE	TOOLS		MEM
							AUDIO DISPLAY	CH
				TOP MENU		MENU
						T.EDIT
DVD	BD	TV	HDMI	ST	ENTER	ST	TV CTRL	RECEIVER
DVR 1	DVR 2	CD	CD-R
				CATEGORY		RETURN
FM/AM	XM	SIRIUS	iPod USB	SETUP	TUNE		MAIN	ZONE 2

iPod CTRL

INPUT

1Switch on the receiver and your TV.

2Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Place the microphone so that it’s about ear level at your normal listening position (use a tripod if possible). Make sure there are no obstacles between the speakers and the microphone.

CONTROL ON/OFF SPEAKERS ST – ST +

The Auto MCACC display appears once the microphone is connected.1

1.Auto MCACC

Surround Back System

[ Normal ]

Save SYMMETRY to

[ M1.MEMORY 1 ]

START

ENTER:Start :Cancel

3Make sure ‘Normal’ is selected,2 select an MCACC preset3, press RECEIVER and then select START4.

4Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a comfortable volume level.

5Wait for the test tones to finish, then confirm the speaker configuration in the OSD.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.5

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed, the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in step 6.

•With error messages (such as Too much ambient noise! or Check Microphone.) select RETRY after checking for ambient noise (see Problems when using the Auto MCACC Setup on page 11) and verifying the mic connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

1.Auto	MCACC				1.Auto	MCACC
Now	Analyzing…		(2/9)			CHECK!
					Front	[ YES ]
Environment Check					Center	[ YES ]
Ambient Noise		[	OK ]		Surr	[ YES ]
Microphone		[	]		SB	[ YES x 2 ]
Speaker YES/NO		[	]		SW	[ YES ]
		:Cancel		10			OK	:Cancel

Note

1• You can’t use the System Setup menu in either the main or sub zone when the iPod USB, XM or SIRIUS Radio input source is selected. When you set ZONE 2 to ON (page 63), you can’t use the System Setup menu.

•If you cancel the Auto MCACC Setup, or leave an error message for over three minutes, the screen saver will appear.

2• If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Surround back speaker setting on page 42 and make sure to connect your speakers as necessary before continuing to step 4.

•If you have THX-certified speakers, select CUSTOM and choose YES for the THX Speaker setting.

3The six MCACC presets are used for storing surround sound settings for different listening positions. Simply choose an unused preset for now (you can rename it later in Data Management on page 47).

4Note that correction curves are saved only when set to SYMMETRY. Select CUSTOM to save other correction curves (such as ALL CH ADJUST and FRONT ALIGN). See Automatic MCACC (Expert) on page 39 for more on this.

5Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

10

En