Front Panel Features, Rear Panel Features

FRONT PANEL FEATURES

2					17
3					13
					13
			18
1		19			10
		19
					12
		4		4
7	6	5	7	6	5
8		15	16		8

1.Mic Gain: This knob adjusts the volume of the microphone input.

2.Mic Treble: Adjusts the high-tone of the microphone.

3.Mic Bass: Adjusts the low-tone of the microphone.

4.Channel Gain: Adjusts the pre-fader input level.

5.Channel Treble: Adjusts the high-tone level.

6.Channel Middle: Adjusts the middle-tone level.

7.Channel Bass: Adjusts the low-tone level.

8.Input Selector: Selects what input source is routed to the channel from the rear panel connected units.

9.Channel Fader: Adjusts the level sent to program mix.

10.Headphone Volume: Adjusts the volume level of the headphone output.

11.Headphone Jack: Your headphones can be connected to this ¼” terminal. The volume should always be set at its lowest setting while connecting and disconnecting headphones to prevent damage to headphones and/or your hearing.

12.Cue Slider: Channels 1 and 2 can be previewed using this mini-crossfader. Sliding this to the left plays the left “channel-1” and sliding to the right plays the right “channel-2”.

13.Master Cue Selector: When selected only the master output is heard in the headphones.

14.Replaceable Crossfader: Blends audio between the channels assigned to the left and right assign switches.

Note: This fader is user replaceable if it should ever wear out. Simply remove the facepanel and then remove the screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer.

15.Crossfader Direction Button: Activation of this switch reverses the assignment of CH-1 and CH-2 on the crossfader.

16.Crossfader Contour Control: The position of this knob determines how quickly or intensely the crossfader will blend.

17.Master Output Knob: Adjusts the main output volume.

18.Audio Spectrum Analyzer: Spectral display of the audio.

19.Display: Selects between various modes of display for Channels 1-2 and master

REAR PANEL FEATURES

		3	4	3	4
9		3		3
9
					1
8
7	6	5	2	5	2

Note: It is recommended that the mixer be turned off before connecting and disconnecting any sources to the inputs of the mixer.

1.Microphone Input: Microphones with a ¼” connector can be connected to this input terminal.

2.Phono Inputs: This input is used for connecting your turntables through the sensitive RIAA phono preamplifiers. Only turntables with phono level output should be attached. Line level turntables and other devices may be attached if the Phono/Line rear panel switch is set to the line position.

3.Phono/Line Source Switch: This switch activates and deactivates the sensitive RIAA phono preamplifiers. Only turntables with phono level output should be assigned when the switch is in the phono position. Some turntables offer line level output. To use these turntables and other line devices like CD players, switch the input to Line.

4.GND: This screw connector should be used to secure any turntables or other devices connected to the mixer that need to be grounded.

5.Line Inputs: CD players, Tape Decks, Samplers or other line level input devices should be connected to these inputs.

6.Record Output: This RCA output is for connecting a recording device such as a tape deck or CD recorder. The level of the record output is based upon pre-master levels.

7.Master Output (RCA): This output is for connecting an external monitoring device such as a PA system, powered monitors or a home stereo. The level of the master stereo output signal is controlled by the master fader.

8.AC In: This mixer is designed to work with the power supply assembly that comes with the unit. While the power is switched off, plug the power supply into the mixer first, then plug it into the outlet.

9.Power Switch: Use this switch to turn on the mixer after all input devices are already connected to prevent damage to your equipment. Turn the mixer on before you turn on amplifiers and turn of amplifiers before you turn off the mixer.