Pioneer VSX-9100TX operating instructions Video, Audio components on

Page 71

Additional information

12

Symptom

Cause

Remedy

Can't record audio.

• You are trying to make an analog recording

• You can only record analog to analog, or digital to

 

from a digital signal, or a digital recording of

digital.

 

an analog source.

 

 

 

 

 

• The digital source is copy protected.

• You can't record digital sources that have been copy

 

 

protected.

 

 

 

 

• The analog REC jacks have not been

• Check your analog connections (see Connecting analog

 

connected properly.

audio components on page 17).

 

 

 

Subwoofer output is very low.

• The speaker settings result in very little

• To route more audio signal to the subwoofer, set it to

 

audio signal being sent to the subwoofer.

PLUS, or select SMALL for the front speaker setting (see

 

 

Speaker Setting on page 44).

Everything seems to be set up

• The speakers are out of phase.

correctly, but the playback sound

 

is odd.

 

•Check that the positive/negative speaker terminals on the receiver are matched with the corresponding terminals on the speakers (see Connecting the speakers on page 20).

Noise or hum can be heard even

• There is electrical interference from another

• Check that personal computers or other digital

when there is no sound being

component or appliance.

components connected to the same power source are not

input.

 

causing interference.

 

 

 

There seems to be a time lag

• The subwoofer channel can be delayed

• See Automatically setting up for surround sound

between the speakers and the

slightly if run through a low-pass filter.

(MCACC) on page 11 to set up your system again using

output of the subwoofer.

 

MCACC (this will automatically compensate for a delay in

 

 

the subwoofer output).

 

 

The maximum volume available

• The channel levels may have been adjusted. • This is not a malfunction. If the levels in Channel Level

(shown in the front panel display)

 

on page 45 have been adjusted, the maximum volume will

is lower than the +12dB

 

change accordingly.

maximum.

 

 

 

 

 

Video

Symptom

Cause

Remedy

 

 

 

No image is output when an input is selected.

• The video connections are incorrect.

• Make sure the video component is connected correctly

 

(see page 18).

 

 

• You are using component video

• Using the video converter, video signals can be

connections for your source, but not for your

converted from a composite or S-video input to a

TV.

component video output, but not vice-versa. See About the

 

video converter on page 15 for more on this.

 

• You are using component video

• Check Assigning the component video inputs on page 64

 

connections and the component video inputs

to make sure you’re assigned the correct input.

 

are assigned incorrectly.

 

 

 

 

• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied

 

 

with the DVD/video player.

 

 

 

 

• The video input selected on the TV monitor

• Set correctly. Refer to the instruction manual supplied

 

is incorrect.

with the TV.

 

 

 

 

• Even though the sub room monitor is

• Press the MULTI ROOM&SOURCE ON/OFF button to

 

connected properly, the multi-room feature is

switch it on.

 

switched off.

 

 

 

 

 

• The component video inputs are assigned

• Check Assigning the component video inputs on page 64

 

to a video component connected only to the

to make sure the component video assign for that video

 

composite or S-Video terminals.

component is switched to OFF.

 

 

 

 

• You connected your TV to the MULTI ROOM

• Connect the MONITOR OUT jack to the TV monitor (see

 

& SOURCE MONITOR OUT jack instead of

Connecting video components on page 18).

 

the main MONITOR OUT jack.

 

 

 

 

The System Setup screen

• Some TVs connected to the receiver with

• When the receiver is in standby, switch to COLOR

doesn't appear.

component video cables do not display the

BURST OFF by holding down the front panel ACOUSTIC

 

System Setup screen when the Color Burst

EQ button and pressing STANDBY/ON. (the current

 

feature is on.

setting appears in the display).

 

 

 

 

• The MONITOR OUT jack hasn't been

• Connect the MONITOR OUT jack to the TV monitor (see

 

connected.

Connecting video components on page 18).

 

• You connected your TV to the MULTI ROOM

 

& SOURCE MONITOR OUT jack instead of the main MONITOR OUT jack.

71

En

Page 70 Page 72
Image 71
Page 70 Page 72
Contents VSX-9100TX Information to User Wash hands after handlingImportant Safety Instructions Contents Additional information Other SettingsControlling the rest of your system Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Installing the receiverBefore you start Ventilation Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterSurround speakers Powered subwooferMinute guide Front speakers02 5 minute guide Enter Make sure ‘Normal SB’ is selected then pressFollow the instructions on-screen Playing a source Checking the settings on your DVD or other playerOther problems when using the Auto Mcacc Setup About cable types Connecting upConnecting up Chapter About the video converter Connecting upCD recorder DVD or LD player CD player Connecting up Connecting digital audio componentsTip Connecting up Connecting analog audio componentsConnecting multichannel analog components Output jacksDVD or LD player Connecting up Connecting video componentsConnecting to the front panel video terminal TV tunerAM loop antenna Connecting up Connecting antennasFM wire antenna Using external antennasFront speakers Connecting the speakersHints on speaker placement Overhead view of speaker setupAC outlet Connecting upPower cord caution View of 7.1 channel speaker setupFront panel Listening Mode SelectControls and displays Controls and displays ChapterControls and displays Controls and displays Display Sleep StereoMono TunedControls and displays Remote control Tuner Display 6TUNE/ST +/- /ENTERDTV ON/OFF DTV InfoOperating range of remote control unit Auto playback Listening to your systemListening to your system Chapter Listening in surround soundPRO Logic Using the Home THX modesUsing the Advanced surround effects Listening to your systemPress EFFECT/CH SEL again to adjust other settings Dolby Pro Logic IIx Music settingsNeo6 Music settings Use the +/- buttons to adjust the settingListening to your system Listening with Acoustic Calibration Choosing the input signalTo cycle the surround back channel options Listening to your system Using the surround back channelExtended mode Press Extended Mode front panel repeatedlyMode VirtualSB Listening to your system Using the Virtual Surround BackEnhancing dialog Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Press Tone to select the frequency you want to adjust30 min Using the sleep timerListening to your system Playing other sources Selecting the multichannel analog inputsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘MANUAL MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Channel Distance Fine Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallyCopying your Acoustic Calibration EQ settings Front Align Setting the Acoustic Calibration EQ manuallyChecking your Acoustic Calibration EQ settings Select ‘Manual SP Setup’ then press Enter Manual speaker setupSelect the setting you want to check Select ‘Speaker Setting’ from the Manual SP Setup menu Speaker SettingChannel Level Crossover NetworkSpeaker Distance Select ‘Speaker Distance’ from the Manual SP Setup menuListening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationAbcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presetsPrepare the recorder Making recordingsMaking recordings Chapter Making an audio or a video recordingControlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemPress the Receiver button to exit and store the operations Use cursor left/right to select Learn then press EnterDirect function Erasing all of the remote control presetsConfirming preset codes Disc Controlling the rest of your system Controls for TVsInput SelectSHIFT+ CD/MD/CD-R/DVD/LDShift + DVD Controlling the rest of your systemEnter Guide HDDOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsFront left Speaker Bi-wiring your speakersOther connections Bi-amping your front speakers Making multi-room connections Using the sub room controlsUsing the remote control in the sub room Other connections Multi-room listeningPress the Multi Room ON/OFF button on the front panel Using the front panel multi-room controlsUse the Master Volume dial to adjust the volume Other connectionsUsing this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersDVD player Using the SR+ mode with a Pioneer plasma displayPioneer plasma Page Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the component video inputs Other SettingsOther Setup menu Select ‘Other Setup’ then press EnterChoose the setting that you want Dynamic Range Control SetupDual Mono Setup Select ‘DRC Setup’ from the Other Setup menuSelect ‘SR+ Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘LFE ATT Setup’ from the Other Setup menuVolt Trigger Setup Multi Room SetupAdditional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsAudio components on VideoDisplay SettingsExtended Auto setting, the EX Remote controlPress System Setup to confirm Additional information Resetting the main unitSwitching the speaker impedance Dolby Additional information Surround sound formatsAdditional information About THX Cleaning the unit Additional information SpecificationsDecibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation

VSX-9100TX specifications

The Pioneer VSX-9100TX is a powerful and versatile surround sound receiver that has garnered a strong reputation among audio enthusiasts since its release. Designed to cater to the needs of home theater aficionados, the VSX-9100TX comes packed with features and technologies that elevate the listening experience, making it a noteworthy addition to any audio setup.

One of the standout characteristics of the VSX-9100TX is its robust amplification capabilities. The receiver boasts a 7.1 channel output, delivering an impressive total power of 100 watts per channel. This means that users can experience rich, dynamic sound across multiple audio channels, making it an excellent choice for immersive movie watching or music listening.

Incorporating Dolby Digital EX and DTS-ES technologies, the VSX-9100TX ensures that users can revel in high-quality surround sound, regardless of the source material. This versatility allows for seamless playback of both stereo and multi-channel audio formats, allowing for an expansive soundstage that enhances the overall experience.

Another essential feature of the VSX-9100TX is its advanced room calibration technology. The built-in MCACC (Multi-Channel Acoustic Calibration System) optimizes sound output by analyzing the room's acoustics and adjusting the speaker settings accordingly. This results in a more balanced and natural sound that adapts to your specific environment, ensuring that every listener can enjoy optimal audio quality.

Connectivity options are plentiful with the VSX-9100TX, featuring multiple HDMI inputs, component video inputs, and analog audio inputs, making it highly adaptable to various media sources. Additionally, the receiver supports video upscaling, allowing users to enhance the quality of standard-definition sources to a higher resolution for improved viewing experiences.

The VSX-9100TX also includes a user-friendly interface, allowing easy navigation through its array of settings and features. The remote control provides intuitive access to various functions, making it convenient for users to switch between inputs, adjust volume, or engage different sound modes with ease.

In conclusion, the Pioneer VSX-9100TX stands out with its impressive amplification, cutting-edge audio technologies, and user-friendly features. Whether for movies, music, or gaming, this receiver is designed to deliver an exceptional audio experience, setting a standard that resonates with audiophiles and casual listeners alike. Its combination of power, versatility, and advanced sound calibration makes it a compelling choice for anyone looking to enhance their home theater system.
Top Page Image Contents