Telex N/DYM SERIES manual Table of Contents, Quick System Setup Guide

Page 2

ENGLISH

Table of Contents

1.Quick System setup guide

2.System Description

3.Detailed system/component setup instructions

3.1Receiver Setup & Operation

3.2Handheld Transmitter Setup

3.3Beltpack Setup

4.Guidelines/Recommendations for best performance

5.Troubleshooting Guide

6.Technical Specifications

7.Certifications

8.Components & Accessories

9.Service/Warranty

1. Quick System Setup Guide

Receiver Setup

1.Plug power supply cord into the back of the receiv- er and plug the power supply into an outlet. The channel display & red/green “Diversity” light on the receiver front panel should light up.

2.Depress “SET” button on front panel and release when channel display starts to flash (about 3 seconds). This activates “ClearScanTM” to find an interference free channel for operation. Note the channel (0 - 9) shown on the receiver front panel channel display.

3.Connect receiver audio output to mixer (or amplifier if using guitar system). Mute or reduce mixer/amp gain.

4.Orient receiver antennas angled up and away from each other (at a 90 degree angle).

Transmitter Setup

1.Open battery compartment, install 9 Volt battery. Make sure to observe proper battery polarity.

2.Adjust channel setting to match channel number shown on receiver channel display. Replace battery cover.

3.If using beltpack transmitter, plug the microphone into the transmitter connector. If using guitar system, connect 1/4” plug into guitar.

Operating the system

1.Turn transmitter ON via the ON/OFF switch. Yellow “Tx On” light should illuminate on the receiv- er front panel.

2.Turn audio switch to the ON position to unmute the audio.

3.Set mixer/amp gain to normal position.

4.Talk/sing into the microphone or play the guitar at a normal volume. You should hear audio coming out of the system.

5.If the signal is distorted, turn the gain adjust con- trol on the transmitter down. If the signal level is low, you may need to turn the gain adjust control up.

6.If connected to the receiver 1/4” output jack on the front panel, adjust gain (via the control next to the connector) to correspond to the signal level found when singing or playing through a wired system.

Image 2
Contents DYM Series Wireless User Guide Table of Contents Quick System Setup GuideReceiver Setup & Operation Detailed Setup InstructionsSystem Features System DescriptionOnce the Transmitter has been set-up, Handheld Transmitter Setup PA / sound systemBodypack Transmitter Setup Guidelines/Recommendations for best performance Troubleshooting Guide Problem Possible Causes SolutionsUHF Transmitters NBPU, NBPU-G, NHTU-N1, NHTU-N2 DYM Wireless Series System Technical SpecificationsUHF Receivers NRU and NRU-G Receivers Accessories & Parts CertificationsFactory Service Warranty LimitedService/Warranty North America

N/DYM SERIES specifications

Telex N/DYM SERIES is a line of professional dynamic microphones designed specifically for broadcast, recording, and live sound applications. Renowned for their high-quality audio capture and robust build, these microphones are a staple in the audio engineering world and are favored by artists, sound engineers, and broadcasters alike.

One of the standout features of the Telex N/DYM SERIES is its use of neodymium magnet technology. This allows for a higher output level and improved sensitivity compared to traditional dynamic microphones. Neodymium magnets provide an efficient transduction mechanism, enabling the microphone to capture a wider frequency range with great clarity and detail. The result is a microphone that can accurately reproduce vocals and instruments with remarkable fidelity.

Another key characteristic of the N/DYM SERIES is its cardioid polar pattern. This design helps to minimize ambient noise and feedback by focusing on sound coming from directly in front of the microphone while rejecting sounds from the sides and rear. This makes it particularly useful in live environments where stage noise and audience interference can be problematic, allowing performers to deliver their sound without unwanted distractions.

Durability is also a major focus of the Telex N/DYM SERIES. Built to withstand the rigors of professional use, these microphones feature a rugged construction that can handle the inevitable wear and tear of on-stage performances. The sturdy grill and housing help protect the internal components, ensuring that the microphone maintains its performance and reliability over time.

Furthermore, the N/DYM SERIES microphones often come equipped with advanced internal shock-mount systems. These systems reduce handling noise and vibrations that could otherwise color the sound. This is crucial in both studio and live settings where clarity is of paramount importance.

The versatility of the Telex N/DYM SERIES is another factor that makes it a popular choice among audio professionals. Whether it’s used for vocal performances, acoustic instruments, or amplified sound sources, the microphone adapts well to a variety of applications. The series ensures that users can achieve outstanding results across different scenarios, from studio recordings to live gigs.

In summary, the Telex N/DYM SERIES combines high-quality neodymium technology, a cardioid polar pattern, rugged construction, and innovative design features to create microphones that excel in both live and studio settings. This comprehensive range of characteristics makes the N/DYM SERIES a reliable and effective choice for those seeking exceptional audio quality and durability in their microphone applications.